Manuals / Intel / Computer Equipment / Switch

Intel 654655-001 manual packets or bytes received packets forwarded

Models: 654655-001

1 83

Download 83 pages 573 b

Page 56

C H A P T E R 2 Intel Express 100BASE-TX Switching Hub

get-sdist-cntget-sdist-cnt <port>

Displays the RMON statistics packet size histogram for port. SYS_console> get-sdist-cnt 3

RMON Packet Size Distribution Counters for port 3

============================================================

etherStatsPkts64Octets	:	4352
etherStatsPkts65to127Octets	:	19845
etherStatsPkts128to255Octets	:	673
etherStatsPkts256to511Octets	:	1209
etherStatsPkts512to1023Octets	:	1471278
etherStatsPkts1024to1518Octets :		52163

get-br-cntget-br-cnt<port-number>

Displays the switching statistics counters for a port. The command displays the number of:

•packets or bytes received.

•packets forwarded.

•multicast packets.

•packets with unknown destination and subsequently multicast.

•packets transmitted.

•packets lost (if flow control is disabled) or number of packets retransmitted by the originator due to flow control (if flow control is enabled).

•packets or bytes forwarded to each port. For the port you specified, the number of packets or bytes represents filtered frames. Filtered frames are ones that don’t need to be forwarded because they’re destined for the same port they came in on.

SYS_console> get-br-cnt 3

Ethernet Switching Counters for port 3

====================================================


Frm	Received OK :		1419681
Bytes Received		: 842637991
Frm Filtered		:	0
Frm to all ports		:	0
Frm multicast		:	16017
Frm lost/fctrl		:	0
Transmit OK		:	1404387

52

Image 56

Intel 654655-001 manual packets or bytes received packets forwarded

Contents

Intel Express 100BASE-TXSwitching Hub User GuideFirst edition Contents Hardware Installation and Network TopologyConfiguring and Managing the Switch Quick StartTroubleshooting ChapterAppendix A Technical InformationQuick Start Console MgmtOptional Quick Start for SNMP Management Hardware Installation and NetworkTopology OverviewFeatures Installation and Setup 1 Install the switch in a rack or on a shelf2 Plug the switch in and turn the power on 4 Is setup complete?Using the Switch Port status LEDsManagement status LEDs Console MgmtFiber optic requirements Cabling RequirementsUTP requirements Determining which cable to use Connector pinoutsStraight-throughvs. crossover cables Typical Configurations Configuring the 100 Mbps workgroup environment100 Mbps clients using 100 Mbps clients usingConfiguring the Wide Area Network WAN environment or Switch ofSwitches BackboneConnecting to a 10 Mbps segment Switching HubServer equipped with two adapters, one atBy default, flow control is enabled on all ports Excessive flow control problemsRepeater count limitations Page Configuring and Managing the SwitchConsole Mgmt Accessing the Console ManagerAccessing the Console Manager remotely Using the Console Manager Entering commandscP at the prompt Commands used Console Manager command groupsConfiguring a port for full duplex Configuring the SNMP agent for IP To configure a port for full duplexCommands used To configure the SNMP agentTo check traffic on a port Monitoring trafficCommands used Creating VLANs To create an SVLAN To create a VBDConfiguring the spanning tree Creating custom filtersConsole Command Reference To set a custom filterlogin help-kbdbanner clearSystem commands logoutset-prompt set-passwdsys-stat warm-resetcold-reset get-last-err init-nvramset-line-slip set-sw-fileIP commands set-par-fileset-fg-param start-fgIP Configuration get-ipget-ip-conf set-ipget-bootp set-bootpset-ip-conf get-slipC H A P T E R get-arp-tbl Address Resolution Protocol ARP Commandsping-stop SNMP commands SNMP community stringsSNMP trap message commands set-commget-auth set-authdel-trap Switching database commandsadd-trap The entry has these properties C H A P T E R Configuring and Managing the Switchget-lt-16 del-lt-addr find-lt-addrdel-lt-entry set-lt-age add-lt-entryget-lt-age add-cf-entry Custom filteringget-lt-filter del-cf-entry get-nv-cftblget-nv-cfilt C H A P T E Rget-vbc-matrix VLAN commandsget-con-matrix set-vbc-domain del-vbc-domainget-vbc-tbl set-sec-vlanSpanning tree commands del-sec-vlanget-svlan-tbl set-mon-portget-stp set-stpget-st-bcfg get-st-pcfgset-br-hellot set-br-fwdelset-prt-prio set-prt-enbset-port-dplex Port configuration commandsget-port-cfg Switching statistics commands set-port-fctrlclr-cnt get-eth-cntC H A P T E R get-colls-cntget-rmon-cnt packets or bytes received packets forwarded C H A P T E R Configuring and Managing the Switchget-mgm-brcnt Console command-linesummary Console CommandsSystem Commands IP CommandsSwitching Database Commands IP Commands con’tSNMP Commands Port Configuration Commands Virtual LAN VLAN CommandsSpanning Tree Commands Switching Statistics Commands C H A P T E RPage 3 Troubleshooting message Default Configuration A Technical InformationSpecifications FeaturesPorts Console ManagerStatus Indicators per port General IndicatorsBoot and Configuration Connector Interfaces115 volt configuration 230 volt configurationElectrical Specifications Power Cord SpecificationsSNMP and MIB Support Custom Filter Port Table Source PortsSource Ports con’t Destination Ports Destination Ports con’t 0,3,4,5,6 0,3,4,5,7 B9 0,3,4,6,7 D9 0,3,5,6,7 E9 Limited Warranty FCC NoticeManufacturer declaration A p p e n dPage I Index Page Page Page Page Page World Wide Web CompuServeIntel BBS FaxBack