Manuals / Intel / Computer Equipment / Switch

Intel 654655-001 manual add-lt-entry, get-lt-age, set-lt-age

Models: 654655-001

1 83

Download 83 pages 573 b

Page 45

C H A P T E R 2

Configuring and Managing the Switch

add-lt-entry

add-lt-entry <mac_address> {lock-offlock-on} <dport>

Add an entry to the switching database. The lock setting is described at the beginning of this section. dport is the destination port number.

add-lt-entry 00-A0-C9-00-11-11 lock-off 3

This command sends packets from the device with MAC address

00-A0-C9-00-11-11 to port 3. lock-offmeans the entry is deleted if the device is inactive for 300 seconds (the default aging time).

get-lt-age

Displays the switching database aging time in seconds. This is the amount of time the switch stores a device’s MAC address before clearing it from the database. An entry whose MAC address doesn’t appear in the source field of an incoming packet for this period of time is discarded. The default is 300 seconds.

SYS_console> get-lt-age

The running aging time is: 300 seconds

set-lt-age

set-lt-age {runnvramall} <aging_time>

Modifies the switching database aging time.

The aging_time is in seconds with a default of 300 seconds and a range of 1 to 55,000 seconds. Lower the time if the number of active workstations is larger than 1024.

SYS_console> set-lt-age run 280

Aging Period update in the running database OK

SYS_console> set-lt-age all 100

Aging Period update in NVRAM OK

Aging Period update in the running database OK

41

Image 45

Intel 654655-001 manual add-lt-entry, get-lt-age, set-lt-age

Contents

User Guide Intel Express 100BASE-TXSwitching HubFirst edition Hardware Installation and Network Topology ContentsConfiguring and Managing the Switch Quick StartChapter TroubleshootingAppendix A Technical InformationConsole Mgmt Quick StartOptional Quick Start for SNMP Management and Network Hardware InstallationTopology OverviewFeatures 1 Install the switch in a rack or on a shelf Installation and Setup2 Plug the switch in and turn the power on 4 Is setup complete?Port status LEDs Using the SwitchConsole Mgmt Management status LEDsCabling Requirements UTP requirementsFiber optic requirements Connector pinouts Straight-throughvs. crossover cablesDetermining which cable to use Configuring the 100 Mbps workgroup environment Typical Configurations100 Mbps clients using 100 Mbps clients usingor Switch of Configuring the Wide Area Network WAN environmentSwitches BackboneSwitching Hub Connecting to a 10 Mbps segmentServer equipped with two adapters, one atExcessive flow control problems Repeater count limitationsBy default, flow control is enabled on all ports Page Managing the Switch Configuring andAccessing the Console Manager Accessing the Console Manager remotelyConsole Mgmt Entering commands Using the Console ManagercP at the prompt Console Manager command groups Configuring a port for full duplexCommands used To configure a port for full duplex Configuring the SNMP agent for IPCommands used To configure the SNMP agentMonitoring traffic Commands usedTo check traffic on a port Creating VLANs To create a VBD To create an SVLANCreating custom filters Configuring the spanning treeTo set a custom filter Console Command Referencehelp-kbd loginbanner clearlogout System commandsset-prompt set-passwdwarm-reset cold-resetsys-stat init-nvram get-last-errset-line-slip set-sw-fileset-par-file IP commandsset-fg-param start-fgget-ip IP Configurationget-ip-conf set-ipset-bootp get-bootpset-ip-conf get-slipC H A P T E R Address Resolution Protocol ARP Commands ping-stopget-arp-tbl SNMP community strings SNMP commandsset-comm SNMP trap message commandsget-auth set-authSwitching database commands add-trapdel-trap The entry has these properties Configuring and Managing the Switch get-lt-16C H A P T E R find-lt-addr del-lt-entrydel-lt-addr add-lt-entry get-lt-ageset-lt-age Custom filtering get-lt-filteradd-cf-entry get-nv-cftbl del-cf-entryget-nv-cfilt C H A P T E RVLAN commands get-con-matrixget-vbc-matrix del-vbc-domain set-vbc-domainget-vbc-tbl set-sec-vlandel-sec-vlan Spanning tree commandsget-svlan-tbl set-mon-portset-stp get-stpget-st-bcfg get-st-pcfgset-br-fwdel set-br-hellotset-prt-prio set-prt-enbPort configuration commands get-port-cfgset-port-dplex set-port-fctrl Switching statistics commandsclr-cnt get-eth-cntget-colls-cnt get-rmon-cntC H A P T E R packets or bytes received packets forwarded Configuring and Managing the Switch get-mgm-brcntC H A P T E R Console Commands Console command-linesummarySystem Commands IP CommandsIP Commands con’t SNMP CommandsSwitching Database Commands Virtual LAN VLAN Commands Spanning Tree CommandsPort Configuration Commands C H A P T E R Switching Statistics CommandsPage 3 Troubleshooting message A Technical Information Default ConfigurationFeatures SpecificationsPorts Console ManagerGeneral Indicators Status Indicators per portBoot and Configuration Connector Interfaces230 volt configuration 115 volt configurationElectrical Specifications Power Cord SpecificationsSNMP and MIB Support Source Ports Custom Filter Port TableSource Ports con’t Destination Ports Destination Ports con’t 0,3,4,5,6 0,3,4,5,7 B9 0,3,4,6,7 D9 0,3,5,6,7 E9 FCC Notice Limited WarrantyManufacturer declaration A p p e n dPage I Index Page Page Page Page Page CompuServe World Wide WebIntel BBS FaxBack