Intel MD566X - page 102

56K V.92 Data, Fax, and Voice Chipset

102 Intel Confidential Programmer’s Guide

S3 13

Carriage Return Character: S3 specifies the AT command string terminator and

modem response code terminator. The factory default is a <CR> or carriage return

(ASCII decimal 13).

Range: 0–127

Default: 13 (Carriage Return)

S4 10

Line Feed Character: S4 specifies the line feed character, which is used for verb ose

(text) modem result codes.

Range: 0-127

Default: 10 (line feed)

S5 8

Backspace Character: S5 specifies the backspace character that is used to delete

the last-entered character. After receiving a backspace characte r, the modem sends

three characters to the DTE: a backspace character, a space character, and then an-

other backspace character.

Range: 0–32, 127

Default: 8 (BS)

S6 2

Wait Before Blind Dialing: S6 specifies the amount of time that must elapse after

the modem goes off-hook before the modem starts dialing the first telephone num-

ber. The modem waits for at least 2 seconds before dialing the first nu mber, even if

S6 is set for a value less than 2. S6 is only used for result code type commands X0,

X1, and X3 (that is, blind-dialing types of result codes). Resu lt code types X2 and X4

enable dial-tone detection and ignore the contents of S6.

Range: 2–255 seconds

Default: 2 seconds

S7 60

Wait for Carrier/Dial Tone: S7 specifies the length of time that the modem waits to

detect the remote modem carrier after dialing the telephone number. If the remote

modem carrier is not detected within the S7 time limit, the modem hangs up and

sends a ‘NO CARRIER’ response code to the DTE. If the remote modem carrier is

detected, the modem goes into online data mode and sends a “CONNECT” mes-

sage to the DTE.

S7 also specifies the time duration for the ‘@’ (wait for quie t answer) dial modifier.

Range: 1–255 seconds

Default: 60 seconds

S8 2

Pause Time for Dial Modifier: S8 specifies the length of time that the mo dem paus-

es during the dialing process each time the ‘,’ dial modifier is detected i n the dialing

string.

Range: 0–255 seconds

Default: 2 seconds

Table 7-1. S-Register Command Descriptions (Continued)

Contents

Main MD566X 56K Data, Fax, and Voice Chipset Revision History Date Revision May 2001 Revise layout. July 2001 Update for V.92 Programmers Guide Intel Confidential CONVENTIONS Abbreviations Acronyms Acronym Definition (Continued) Programmers Guide Intel Confidential 1. INTRODUCTION Table 1-1. Intel V.90/V.92 56K Chipsets 1.1 V.92, V.90 and V.34 Data Modes 1.2 Modem Connection Overview Programmers Guide Intel Confidential Table 1-2. DTE-to-DCE Data Rates for Each Mode Table 1-3. DCE-to-DCE Data Rates for Each Mode 2. AT COMMAND SUMMARY TABLES Table 2-1. Data Mode Command Summary Note Command Function Default Range Reported by &Vn 56K V.92 Data, Fax, and Voice Chipset Note Command Function Default Range Reported by &Vn Page Page Page Page 14 Intel Confidential Programmers Guide Table 2-2. V.44 / V.42 / V.42 bis MNP Command Summary Note Command Function Default Range Reported by &Vn Programmers Guide Intel Confidential Table 2-2. V.44 / V.42 / V.42 bis MNP Command Summary (Continued) Note Command Function Default Range Reported by &Vn Page Programmers Guide Intel Confidential Table 2-3. Fax Identity Command Summary Table 2-4. Fax Class 1 Command Summary Table 2-5. IS-101 Voice Command Summary 18 Intel Confidential Programmers Guide Table 2-5. IS-101 Voice Command Summary (Continued) Table 2-6. Voice DTEDCE Character Pairs Response Hex Code Function Programmers Guide Intel Confidential Table 2-7. Voice DTEDCE Character Pairs Response Hex Code Function 20 Intel Confidential Programmers Guide Table 2-8. Dial Modifiers Command Function Note R egister Function Default Range Units Table 2-9. S-Register Summary Reported by &Vn Programmers Guide Intel Confidential Table 2-9. S-Register Summary (Continued) Table 2-10. V.90/V.92 Mode DCE-to-ISP Response Codes 22 Intel Confidential Programmers Guide Table 2-11. V.34 Mode DCE-to-DCE Response Codes Verbose Code Numeric Code Table 2-12. DTE-to-DCE Data Rate Response Codes Verbose Code Numeric Code Programmers Guide Intel Confidential Table 2-13. Manufacturing-Only Command Summary 3. BASIC DATA MODE AT COMMANDS 3.1 Using AT Commands to Access the S-Registers [Sn?, Sn=x, ?] 3.2 Modem Responses and Command Echo [En, Vn, Xn, Wn, Qn] Programmers Guide Intel Confidential 3.3 Modem Reset and NVRAM Commands [DS=n, Zn, &F, &Vn, &Yn, &Wn, &Zn=x] Table 3-1. Product Identification Information 3.5 Establishing a Modem Connection [A, D, DS = n, S0] 3.6 Online Command Mode [Escape Codes, On] 3.7 Hanging Up [Hn, S10, Zn, &D2] 3.8 Modem-to-Modem Connection Data Rates Page Page Page Page Programmers Guide Intel Confidential Table 3-2. Supported Modulation Types Page Programmers Guide Intel Confidential Table 3-3. Resulting DCE-to-DCE Connection Rates with Non-Default Value s 3.9 Diagnostic Testing [S18, &Tn] 3.9.1 Local Analog Loopback [AT&T1] LOCAL MODEM Figure 3-2. Local Analog Loopback Test Local Modem (or Test Modem) Page 3.9.2 Local Analog Loopback With Self-Test [AT&T8] Figure 3-3. Local Analog Loopback with Self-Test Local Modem (or Test Modem) Programmers Guide Intel Confidential 3.10 AT Escape Sequences 3.10.1 Time-Independent Escape Sequence Licensing Requirements for Hayes Escape Sequence 3.10.2 Hayes Escape Sequence En, Hn, Mn, On, Qn, Sn, Vn, Xn, and & commands (except &Tn and &F) Page Page Page Page Programmers Guide Intel Confidential (cont.) 0 Identification/Checksum Option: (cont.) Page Page Programmers Guide Intel Confidential Wn 0 Page Page Page Page Page Page Page Page Page Page Page Page Page Programmers Guide Intel Confidential 4. ERROR CORRECTION AND DATA COMPRESSION Operating Modes Table 4-1. Resulting \Nn Connection Types Page Page Page Page Page Page +DS44=m 3,0,0,471, 972,140, 140,1884, 3768 5. FAX CLASS 1 AT COMMANDS 5.1 Fax Identity Commands Table 5-1. Fax Identity Command Descriptions Programmers Guide Intel Confidential Table 5-1. Fax Identity Command Descriptions 5.2 Fax Clas s 1 Commands Figure 5-1. T.30 HDLC Frame Format Table 5-2. <mod> Selection Table Programmers Guide Intel Confidential Figure 5-2. CLASS 1 DTE-Generated HDLC Frame Information (AT+FTH=<mod>) Figure 5-3. CLASS 1 DTE Reception of HDLC Frame Information (AT+FRH=<mod>) Table 5-3. Fax Mode Command Descriptions Page Page 6. IS-101 VOICE MODE AT COMMANDS 6.1 DTMF Detection 6.2 Relay Control Table 6-1. Voice Mode Command Descriptions Page Page Page Page Programmers Guide Intel Confidential Table 6-1. Voice Mode Command Descriptions (Continued) 15678 2 } } Page Programmers Guide Intel Confidential +VLS=n 0 Preassigned Voice I/O Labels Table 6-1. Voice Mode Command Descriptions (Continued) <label> Primitive Code Description Voice I/O Primitive Codes Table 6-1. Voice Mode Command Descriptions (Continued) Page Page Page Page Page Page Page Page Page Page Programmers Guide Intel Confidential 7. S-REGISTERS Table 7-1. S-Register Command Descriptions Page Page Page Page Page Programmers Guide Intel Confidential S33 10 Page Page Programmers Guide Intel Confidential 8. CALLER ID Table 8-1. Caller ID Tags for Formatted Reporting Page Programmers Guide Intel Confidential 9. MANUFACTURING-ONLY COMMANDS Table 9-1. Manufacturing-Only Command Descriptions Page Page Page Page Page 10. PARALLEL HOST INTERFACE 16C450/16C550A UART Figure 10-1. FIFO Buffers for Transmitter and Receiver 120 Intel Confidential Programmers Guide Table 10-1. Parallel Host Interface UART Register Bit Assignments Note: These bits are always 0 in 16C450 mode. 10.1 UART Register Definitions 10.1.1 Scratch Register (SCR) Register 5 10.1.2 Modem Status Register (MSR) 10.1.3 Line Status Register (LSR) 10.1.4 Modem Control Register (MCR) Register 4 10.1.5 Line Control Register (LCR) Register 3 10.1.6 FIFO Control Register (FCR) Register 2 Programmers Guide Intel Confide ntial 125 10.1.7 Interrupt Identity Register (IIR) Table 10-2. Interrupt Control Functions FIFO Mode Only Interrupt Identification Register Interrupt Source and Reset Functions FIFO EN FIFO EN 0 VDMA Int. ID 2 Int. ID 1 Int. ID 0 Int. Pen. 10.1.8 Interrupt Enable Register (IER) 10.1.9 Transmitter Holding Register (THR) 10.1.10Receiver Buffer Register (RBR) Register 1 10.1.11Divisor Latch Registers (DLM and DLL) 10.2 16C550A UART FIFO Operation 10.2.1 FIFO Interrupt Mode Operation Table 10-3. Programmable Data Rates Register 1 10.2.2 FIFO Polled Mode Operation