Intel MD566X - page 79

56K V.92 Data, Fax, and Voice Chipset

Programmer’s Guide Intel Confidential 79

+FTM=n none

Transm it Data:The +FTM = <mod> command causes the modem to transmit

data using the modulation selected in <mod>.

The modem returns a “CONNECT” result code and transmits the proper training

sequence in the selected mode, followed by cons tant “1” bits until data is received

from the DTE. The modem terminates this command upon detecting <DLE><ETX>

characters in the data stream.

If the modem’s transmit buffer empties and the last transmitted character is an

ASCII NULL (00), the modem continues to transmit NULLs until the DTE sends

more data or 5 seconds have elapsed. After 5 seconds have elaps ed with an emp-

ty transmit buffer, the DCE turns off the transmit carrier, returns to command state,

and returns an “ERROR” result code to the modem.

Note: Hex $00 replication does not provide the required timing needed for

generating the TCF frame (1.5 seconds of ‘0’s’).

If the modem’s transmit buffer empties and the last transmi tted character was not

a NULL, the modem turns off the transmit carrier, returns to command state, and

sends the “OK” result code to the DTE.

Note: If the modem is on-hook, the modem always returns an “ERROR”

message to the DTE after receiving the +FTM = <mod> command.

Range: <mod> = 24, 48, 72, 73, 74, 96, 97, 98, 121, 122, 145, 146

Refer to Table5- 2 on page 74.

+FTS=n none

Stop Transmission and Pause:The +FTS=<TIME> command causes the mo-

dem to stop all transmissions. The modem waits for the specified amount of time,

then sends an “OK” result code to the DTE. The value <TIME> is in 10-ms inter-

vals.

Range: <TIME> = 0–255 (in 10-ms intervals)

Table 5-3. Fax Mode Command Descriptions (Continued)

Note: An asterisk (*) denotes the factory-default setting.

Command Default Description

Contents

Main MD566X 56K Data, Fax, and Voice Chipset Revision History Date Revision May 2001 Revise layout. July 2001 Update for V.92 Programmers Guide Intel Confidential CONVENTIONS Abbreviations Acronyms Acronym Definition (Continued) Programmers Guide Intel Confidential 1. INTRODUCTION Table 1-1. Intel V.90/V.92 56K Chipsets 1.1 V.92, V.90 and V.34 Data Modes 1.2 Modem Connection Overview Programmers Guide Intel Confidential Table 1-2. DTE-to-DCE Data Rates for Each Mode Table 1-3. DCE-to-DCE Data Rates for Each Mode 2. AT COMMAND SUMMARY TABLES Table 2-1. Data Mode Command Summary Note Command Function Default Range Reported by &Vn 56K V.92 Data, Fax, and Voice Chipset Note Command Function Default Range Reported by &Vn Page Page Page Page 14 Intel Confidential Programmers Guide Table 2-2. V.44 / V.42 / V.42 bis MNP Command Summary Note Command Function Default Range Reported by &Vn Programmers Guide Intel Confidential Table 2-2. V.44 / V.42 / V.42 bis MNP Command Summary (Continued) Note Command Function Default Range Reported by &Vn Page Programmers Guide Intel Confidential Table 2-3. Fax Identity Command Summary Table 2-4. Fax Class 1 Command Summary Table 2-5. IS-101 Voice Command Summary 18 Intel Confidential Programmers Guide Table 2-5. IS-101 Voice Command Summary (Continued) Table 2-6. Voice DTEDCE Character Pairs Response Hex Code Function Programmers Guide Intel Confidential Table 2-7. Voice DTEDCE Character Pairs Response Hex Code Function 20 Intel Confidential Programmers Guide Table 2-8. Dial Modifiers Command Function Note R egister Function Default Range Units Table 2-9. S-Register Summary Reported by &Vn Programmers Guide Intel Confidential Table 2-9. S-Register Summary (Continued) Table 2-10. V.90/V.92 Mode DCE-to-ISP Response Codes 22 Intel Confidential Programmers Guide Table 2-11. V.34 Mode DCE-to-DCE Response Codes Verbose Code Numeric Code Table 2-12. DTE-to-DCE Data Rate Response Codes Verbose Code Numeric Code Programmers Guide Intel Confidential Table 2-13. Manufacturing-Only Command Summary 3. BASIC DATA MODE AT COMMANDS 3.1 Using AT Commands to Access the S-Registers [Sn?, Sn=x, ?] 3.2 Modem Responses and Command Echo [En, Vn, Xn, Wn, Qn] Programmers Guide Intel Confidential 3.3 Modem Reset and NVRAM Commands [DS=n, Zn, &F, &Vn, &Yn, &Wn, &Zn=x] Table 3-1. Product Identification Information 3.5 Establishing a Modem Connection [A, D, DS = n, S0] 3.6 Online Command Mode [Escape Codes, On] 3.7 Hanging Up [Hn, S10, Zn, &D2] 3.8 Modem-to-Modem Connection Data Rates Page Page Page Page Programmers Guide Intel Confidential Table 3-2. Supported Modulation Types Page Programmers Guide Intel Confidential Table 3-3. Resulting DCE-to-DCE Connection Rates with Non-Default Value s 3.9 Diagnostic Testing [S18, &Tn] 3.9.1 Local Analog Loopback [AT&T1] LOCAL MODEM Figure 3-2. Local Analog Loopback Test Local Modem (or Test Modem) Page 3.9.2 Local Analog Loopback With Self-Test [AT&T8] Figure 3-3. Local Analog Loopback with Self-Test Local Modem (or Test Modem) Programmers Guide Intel Confidential 3.10 AT Escape Sequences 3.10.1 Time-Independent Escape Sequence Licensing Requirements for Hayes Escape Sequence 3.10.2 Hayes Escape Sequence En, Hn, Mn, On, Qn, Sn, Vn, Xn, and & commands (except &Tn and &F) Page Page Page Page Programmers Guide Intel Confidential (cont.) 0 Identification/Checksum Option: (cont.) Page Page Programmers Guide Intel Confidential Wn 0 Page Page Page Page Page Page Page Page Page Page Page Page Page Programmers Guide Intel Confidential 4. ERROR CORRECTION AND DATA COMPRESSION Operating Modes Table 4-1. Resulting \Nn Connection Types Page Page Page Page Page Page +DS44=m 3,0,0,471, 972,140, 140,1884, 3768 5. FAX CLASS 1 AT COMMANDS 5.1 Fax Identity Commands Table 5-1. Fax Identity Command Descriptions Programmers Guide Intel Confidential Table 5-1. Fax Identity Command Descriptions 5.2 Fax Clas s 1 Commands Figure 5-1. T.30 HDLC Frame Format Table 5-2. <mod> Selection Table Programmers Guide Intel Confidential Figure 5-2. CLASS 1 DTE-Generated HDLC Frame Information (AT+FTH=<mod>) Figure 5-3. CLASS 1 DTE Reception of HDLC Frame Information (AT+FRH=<mod>) Table 5-3. Fax Mode Command Descriptions Page Page 6. IS-101 VOICE MODE AT COMMANDS 6.1 DTMF Detection 6.2 Relay Control Table 6-1. Voice Mode Command Descriptions Page Page Page Page Programmers Guide Intel Confidential Table 6-1. Voice Mode Command Descriptions (Continued) 15678 2 } } Page Programmers Guide Intel Confidential +VLS=n 0 Preassigned Voice I/O Labels Table 6-1. Voice Mode Command Descriptions (Continued) <label> Primitive Code Description Voice I/O Primitive Codes Table 6-1. Voice Mode Command Descriptions (Continued) Page Page Page Page Page Page Page Page Page Page Programmers Guide Intel Confidential 7. S-REGISTERS Table 7-1. S-Register Command Descriptions Page Page Page Page Page Programmers Guide Intel Confidential S33 10 Page Page Programmers Guide Intel Confidential 8. CALLER ID Table 8-1. Caller ID Tags for Formatted Reporting Page Programmers Guide Intel Confidential 9. MANUFACTURING-ONLY COMMANDS Table 9-1. Manufacturing-Only Command Descriptions Page Page Page Page Page 10. PARALLEL HOST INTERFACE 16C450/16C550A UART Figure 10-1. FIFO Buffers for Transmitter and Receiver 120 Intel Confidential Programmers Guide Table 10-1. Parallel Host Interface UART Register Bit Assignments Note: These bits are always 0 in 16C450 mode. 10.1 UART Register Definitions 10.1.1 Scratch Register (SCR) Register 5 10.1.2 Modem Status Register (MSR) 10.1.3 Line Status Register (LSR) 10.1.4 Modem Control Register (MCR) Register 4 10.1.5 Line Control Register (LCR) Register 3 10.1.6 FIFO Control Register (FCR) Register 2 Programmers Guide Intel Confide ntial 125 10.1.7 Interrupt Identity Register (IIR) Table 10-2. Interrupt Control Functions FIFO Mode Only Interrupt Identification Register Interrupt Source and Reset Functions FIFO EN FIFO EN 0 VDMA Int. ID 2 Int. ID 1 Int. ID 0 Int. Pen. 10.1.8 Interrupt Enable Register (IER) 10.1.9 Transmitter Holding Register (THR) 10.1.10Receiver Buffer Register (RBR) Register 1 10.1.11Divisor Latch Registers (DLM and DLL) 10.2 16C550A UART FIFO Operation 10.2.1 FIFO Interrupt Mode Operation Table 10-3. Programmable Data Rates Register 1 10.2.2 FIFO Polled Mode Operation