+VIP none | Intel MD566X specs

56K V.92 Data, Fax, and Voice Chipset

Table 6-1. Voice Mode Command Descriptions (Continued)

+VIP none

Initialize Parameter: This command causes the modem to initialize all voice pa- rameters to the factory default values. This command does not change relay or speaker setup (that is, if the modem is off-hook, then the modem remains off hook after processing this command).

DTE / DCE Inactivity Timer: This command sets the length of time the modem can be inactive in voice mode before the modem resets its relays +VLS=0 and changes to data mode (FCLASS=0) with autobauding. The purpose of this timer is to ensure that the DTE does not leave the DCE in a mode that cannot be ac- cessed by voice-unaware software. This timer is supported in playback, record

+VIT=n 0 and voice command mode. Sending any data (such as a <DLE><NUL> string) to the modem re-initializes this timer.

n =0–255 (units of 1.0 second)

n = 0*	Disables inactivity timer
n ≠ 0	Inactivity timer active

88

Intel Confidential

Programmer’s Guide

Image 88

Intel MD566X manual +VIP none

Contents

MD566X Revision History Symbol Units of measure ConventionsProgrammer’s Guide Acronym Definition Dram Introduction Chipset Contents QtyIntel V.90/V.92 56K Chipsets V.92, V.90 and V.34 Data Modes Modem Connection Overview DCE-to-DCE Data Rates for Each Mode DTE-to-DCE Data Rates for Each ModeMode Data Rate bps Affected Data Data Mode Command Summary AT Command Summary TablesCommand Function Default Range Reported by Intel Confidential Data rate Result code type Yes Ports only Async mode +GMI? Intel Confidential V.44 / V.42 / V.42 bis MNP∗ Command Summary Command Function Default Range Reported By &Vn Intel Confidential Value saved in Nvram Fax Class 1 Command Summary Fax Identity Command SummaryIS-101 Voice Command Summary Voice DTE→DCE Character Pairs Response Hex Code Function Voice DTE←DCE Character Pairs Register Function Default Range Units Reported By &Vn Dial Modifiers Command FunctionS-Register Summary 10. V.90/V.92 Mode DCE-to-ISP Response Codes Verbose Code Numeric Code 11. V.34 Mode DCE-to-DCE Response Codes 12. DTE-to-DCE Data Rate Response Codes 13. Manufacturing-Only Command Summary a Command Function Default Range Basic Data Mode AT Commands Using AT Commands to Access the S-Registers Sn?, Sn=x, ?Modem Responses and Command Echo En, Vn, Xn, Wn, Qn Modem Setup Host Command Modem Response Example of a Remote Connection Product Identification Information Information Establishing a Modem Connection A, D, DS = n, S0 Hanging Up Hn, S10, Zn, &D2 Online Command Mode Escape Codes, OnModem-to-Modem Connection Data Rates Intel Confidential Intel Confidential ATH +PMHF +PMHR Supported Modulation Types Carrier Description +MS = carrier , automode, min rate, max rate S37 Originating Answering Resulting Connection Speed Modem Figured to attempt only a 28,800 bps connec Diagnostic Testing S18, &Tn Local Analog Loopback AT&T1 AT&T0 Local Analog Loopback With Self-Test AT&T8 Local Analog Loopback with Self-Test Licensing Requirements for Hayes Escape Sequence AT Escape SequencesTime-Independent Escape Sequence Hayes∗ Escape Sequence Command Default Description Data Mode Command DescriptionsNone Stant carrier mode Dialing Digits Online data mode echo Reports product code Cont ATI5 Mode from online command mode Sn=x Sn? Protocol Lapm Sequent commands to be ignored For data mode Ports asynchronous mode. This command is the same as &M0 User profile n Modem power-up Zn=x None +GMR? +MS=m See m V34BS Modulation Selection Cont +MS=m Examples DTE data rate = 115,200 bpsExamples DTE data rate = 2400 bps +PCW=m +PMH=m +PMHR none DCE +PSS=m Mand Intel Confidential Error Correction and Data Compression Mode Features Resulting \Nn Connection Types Bis with fallback to MNP5 \N3 \An \Bn None \Gn \Cn\Jn \Kn \Nn \Tn \Qn\Xn Intel Confidential +DS44=m 972,140 0,471140,1884 3768 FAX Class 1 AT Commands Fax Identity CommandsFax Identity Command Descriptions Tocols Fax Class 1 Commands +FREV?/+FMR? none Mod Selection Table Value Modulation Speed Bps Class 1 DTE-Generated Hdlc Frame Information AT+FTH=mod Fax Mode Command Descriptions +FCLASS=1 Command Default Description Receive Hdlc Data +FRH=n+FRM=n None +FRS=n None DTE after receiving the +FTH=mod command Data using the modulation selected in mod IS-101 Voice Mode AT Commands Each command may be used as follows Dtmf Detection Relay Control Voice Mode Command Descriptions +FLO=n +VBT=m +VCID=n +VDR=m Enable Report Function+VEM=m See m +VEM=m Dialtone Example 2. Setting the Event Mask Example 3. Reading the Event Mask SettingsEvent Reporting and Masking Example 1. Viewing Supported Events +VGM=n 128 +VGR=n 128+VGS=n +VGT=n +VIP none Code +VLS=n Primitive Code +VLS=n Relay/Playback Control+VNH=n Intel Confidential +VRX none = sds, sdi Defaults m = 128 +VSD=m See ‘m’ Manufac +VSM=m turer- specified Vsr Comments Samples/second Compression Method Selection +VSM=m ManufacVsr Hard Disk +VSP=n +VTD=n 100 +VTS=m none Dtmf and Tone Generation AT+VTS=DTMF or AT+VTS= , ,duration For example AT+VTS= , ,50 Intel Confidential S-Register Command Descriptions Registers Ascii decimal S11 S10S12 S14 138 S16 S21 S22 118 S23 None S27 S31 S33 Maximum Line Speed Attempted 110 Caller ID Caller ID Tags for Formatted Reporting Ring Manufacturing-Only Command Descriptions MANUFACTURING-ONLY CommandsNCnn S91 S92 $TTnn Tone Test Command Analog Loopback ALB Test FAX Test Command Bit Pins #VGP0=n#VGP1=n See Note #VGP2=n 118 Programmer’s Guide Parallel Host Interface 16C450/16C550A Uart119 Parallel Host Interface Uart Register Bit Assignments Register BIT Number Address Name Uart Register Definitions Scratch Register SCRModem Status Register MSR Line Status Register LSR Are no subsequent Fifo errors Modem Control Register MCR Line Control Register LCR 123 Fifo Control Register FCR Trigger Level Bytes Interrupt Control Functions Interrupt Identity Register IIR125 Transmitter Holding Register THR Interrupt Enable Register IER10.1.10Receiver Buffer Register RBR Fifo Interrupt Mode Operation 10.2 16C550A Uart Fifo Operation10.1.11Divisor Latch Registers DLM and DLL Programmable Data Rates Fifo Polled Mode Operation 129 130