+Pmhr | Intel MD566X specification

56K V.92 Data, Fax, and Voice Chipset

Modem-on-Hold: Initiating a Voice Call in Data Mode

Enable MOH

(+PMH=0)

Command Mode

(+++AT)

Request to go on hold

(+PMHR)

Server

Accepts No (Returns 0)

Request?

Yes (Returns 1-13)

Disconnect? No

Flash Hook

(+PMHF)

Yes

Initiate Call

Finish Call

Flash Hook

(+PMHF)

Go Back Online

(ATO)

End Data Connection

(ATH)

32

Intel Confidential

Programmer’s Guide

Image 32

Intel MD566X manual +Pmhr

Contents

MD566X Revision History Symbol Units of measure ConventionsProgrammer’s Guide Acronym Definition Dram Intel V.90/V.92 56K Chipsets Chipset Contents QtyIntroduction V.92, V.90 and V.34 Data Modes Modem Connection Overview Mode Data Rate bps Affected Data DTE-to-DCE Data Rates for Each ModeDCE-to-DCE Data Rates for Each Mode Command Function Default Range Reported by AT Command Summary TablesData Mode Command Summary Intel Confidential Data rate Result code type Yes Ports only Async mode +GMI? Intel Confidential V.44 / V.42 / V.42 bis MNP∗ Command Summary Command Function Default Range Reported By &Vn Intel Confidential Value saved in Nvram IS-101 Voice Command Summary Fax Identity Command SummaryFax Class 1 Command Summary Voice DTE→DCE Character Pairs Response Hex Code Function Voice DTE←DCE Character Pairs S-Register Summary Dial Modifiers Command FunctionRegister Function Default Range Units Reported By &Vn 10. V.90/V.92 Mode DCE-to-ISP Response Codes Verbose Code Numeric Code 11. V.34 Mode DCE-to-DCE Response Codes 12. DTE-to-DCE Data Rate Response Codes 13. Manufacturing-Only Command Summary a Command Function Default Range Basic Data Mode AT Commands Using AT Commands to Access the S-Registers Sn?, Sn=x, ?Modem Responses and Command Echo En, Vn, Xn, Wn, Qn Modem Setup Host Command Modem Response Example of a Remote Connection Product Identification Information Information Establishing a Modem Connection A, D, DS = n, S0 Modem-to-Modem Connection Data Rates Online Command Mode Escape Codes, OnHanging Up Hn, S10, Zn, &D2 Intel Confidential Intel Confidential ATH +PMHF +PMHR Supported Modulation Types Carrier Description +MS = carrier , automode, min rate, max rate S37 Originating Answering Resulting Connection Speed Modem Figured to attempt only a 28,800 bps connec Diagnostic Testing S18, &Tn Local Analog Loopback AT&T1 AT&T0 Local Analog Loopback With Self-Test AT&T8 Local Analog Loopback with Self-Test Time-Independent Escape Sequence AT Escape SequencesLicensing Requirements for Hayes Escape Sequence Hayes∗ Escape Sequence None Data Mode Command DescriptionsCommand Default Description Stant carrier mode Dialing Digits Online data mode echo Reports product code Cont ATI5 Mode from online command mode Sn=x Sn? Protocol Lapm Sequent commands to be ignored For data mode Ports asynchronous mode. This command is the same as &M0 User profile n Modem power-up Zn=x None +GMR? +MS=m See m V34BS Modulation Selection Cont Examples DTE data rate = 2400 bps Examples DTE data rate = 115,200 bps+MS=m +PCW=m +PMH=m +PMHR none DCE +PSS=m Mand Intel Confidential Error Correction and Data Compression Mode Features Resulting \Nn Connection Types Bis with fallback to MNP5 \N3 \An \Bn None \Jn \Cn\Gn \Kn \Nn \Xn \Qn\Tn Intel Confidential 140,1884 3768 0,471+DS44=m 972,140 FAX Class 1 AT Commands Fax Identity CommandsFax Identity Command Descriptions Tocols Fax Class 1 Commands +FREV?/+FMR? none Mod Selection Table Value Modulation Speed Bps Class 1 DTE-Generated Hdlc Frame Information AT+FTH=mod Fax Mode Command Descriptions +FCLASS=1 Command Default Description Receive Hdlc Data +FRH=n+FRM=n None +FRS=n None DTE after receiving the +FTH=mod command Data using the modulation selected in mod IS-101 Voice Mode AT Commands Each command may be used as follows Dtmf Detection Relay Control Voice Mode Command Descriptions +FLO=n +VBT=m +VCID=n +VEM=m See m Enable Report Function+VDR=m +VEM=m Dialtone Example 2. Setting the Event Mask Example 3. Reading the Event Mask SettingsEvent Reporting and Masking Example 1. Viewing Supported Events +VGM=n 128 +VGR=n 128+VGS=n +VGT=n +VIP none Code +VLS=n +VNH=n Relay/Playback ControlPrimitive Code +VLS=n Intel Confidential +VRX none = sds, sdi Defaults m = 128 +VSD=m See ‘m’ Manufac +VSM=m turer- specified Vsr Comments Samples/second Compression Method Selection +VSM=m ManufacVsr Hard Disk +VSP=n +VTD=n 100 +VTS=m none Dtmf and Tone Generation AT+VTS=DTMF or AT+VTS= , ,duration For example AT+VTS= , ,50 Intel Confidential S-Register Command Descriptions Registers Ascii decimal S12 S10S11 S14 138 S16 S21 S22 118 S23 None S27 S31 S33 Maximum Line Speed Attempted 110 Caller ID Caller ID Tags for Formatted Reporting Ring NCnn MANUFACTURING-ONLY CommandsManufacturing-Only Command Descriptions S91 S92 $TTnn Tone Test Command Analog Loopback ALB Test FAX Test Command Bit Pins #VGP0=n#VGP1=n See Note #VGP2=n 118 119 Parallel Host Interface 16C450/16C550A UartProgrammer’s Guide Parallel Host Interface Uart Register Bit Assignments Register BIT Number Address Name Uart Register Definitions Scratch Register SCRModem Status Register MSR Line Status Register LSR Are no subsequent Fifo errors Modem Control Register MCR Line Control Register LCR 123 Fifo Control Register FCR Trigger Level Bytes 125 Interrupt Identity Register IIRInterrupt Control Functions 10.1.10Receiver Buffer Register RBR Interrupt Enable Register IERTransmitter Holding Register THR Fifo Interrupt Mode Operation 10.2 16C550A Uart Fifo Operation10.1.11Divisor Latch Registers DLM and DLL Programmable Data Rates Fifo Polled Mode Operation 129 130