Replacing a Hot Swap Power Supply | Intel SC5300 BRP, SC5300 LX

Maintaining Your Server

Replacing a Hot Swap Power Supply

WARNINGS

Hazardous conditions, power supply: Hazardous voltage, current, and energy levels are present inside the power supply. There are no user-serviceable parts inside it; servicing should be done by technically qualified personnel.

1.Remove power cable from defective power supply.

2.Remove shipping screw (letter “A”) securing Hot Swap Power Supply to chassis, if necessary. Press on green latch (letter “A”) while pulling on handle to remove Hot Swap Power Supply from chassis.

A

B

TP00558

Figure 53. Removing a Hot Swap Power Supply

3.Insert new Hot Swap Power Supply. Replace shipping screw (letter “A”) if shipping chassis to another location.

A

TP00544

Figure 54. Installing a Hot Swap Power Supply

4. Connect power cable to replaced power supply.

46	Intel® Server Chassis SC5300 User Guide

Image 64

Intel SC5300 BRP, SC5300 LX manual Replacing a Hot Swap Power Supply, Removing a Hot Swap Power Supply

Contents

Order Number C51486-003 Intel Server Chassis SC5300 User Guide Preface Manual Organization Additional Information and Software Safety Information Safety Cautions Intel Server Chassis SC5300 User Guide Vii Wichtige Sicherheitshinweise 重要安全指导 Consignes de sécurité Instrucciones de seguridad importantes Xii Intel Server Chassis SC5300 User Guide Xiii Xiv Contents Equipment Log and Worksheets Figures Tables Feature Summary Kit ContentsChassis Description Chassis Front View SC5300 Base Intel Server Chassis SC5300 Base Front View Chassis Front View SC5300 LX with Hot Swap Components Intel Server Chassis SC5300 LX Front View Front Panel Controls and Indicators Pedestal Controls and Indicators Front Panel LED Descriptions Base Chassis Rear View Intel Server Chassis SC5300 Base Chassis Rear View Base Redundant Power and SC5300 LX Chassis Rear View Peripherals Chassis Side ViewHalf-height Peripheral Bays Standard and Optional Hot Swap Drive Bays Accessories and Order Codes Accessories and Order Codes Setting Up the Chassis Installation Safety InstructionsSafety Before You Remove the Access Cover Tools and Supplies Needed Setting Up the Chassis Remove Primary Access Cover Removing the Access Cover Remove Bezel Assembly Removing Bezel Assembly Remove Air Ducts Removing Air Ducts Remove Hot Swap Fans Removing Hot Swap Fans Route Power and Data Cables to the Fixed Drives Removing PCI Add-in Card Retainer Routing Power Cables to Fixed Drives Install 3.5-inch Floppy Drive Routing SCSI/SATA Data Cables Installing Slides on 3.5-in Floppy Drive Install DVD or CD-ROM Drive Installing a DVD or CD-ROM Drive Install Fixed Hard Drives Removing Six-drive Fixed Drive Cage from Chassis Open the lower door Installing Device Slides to Hard Drive Close the lower door of drive cage Install Hot Swap Drives Releasing Drive Carrier from Hot Swap Cage Install Hot Swap Fans Inserting Drive Carrier into Drive Cage Install Server Board Install Air Dam Securing Cables in Chassis with a Hot Swap Power Supply Connect Cables to Server Board Install Add-in Boards Remove PCI Add-in Card Retainer Preparing the Chassis for a PCI Add-in Board Repeat until all PCI add-in cards are installed Reinstall the PCI Add-in Card Retainer Install Air Ducts Removing Inner Plastic Air Baffle from Processor Air Duct Installing Air Ducts Install an Additional Hot Swap Power Supply Module Removing Power Supply Filler Panel Install Bezel Assembly Pedestal Only Installing Bezel Assembly Install Primary Access Cover Installing the Access Cover Setting Up the Chassis Safety Before You Remove the Access Covers Maintaining Your Server Maintaining Your Server Replacing a Fixed Fan For Base and BRP Chassis Only Removing a Fixed Fan Replacing a Hot Swap Fan Removing a Hot Swap Fan Replacing the Front Panel Board Removing the Front Panel Board Replacing a Fixed Power Supply Installing the Front Panel Board Removing Fixed Power Supply Replacing a Hot Swap Power Supply Removing a Hot Swap Power Supply Replacing a Power Distribution Board Removing Hot Swap Power Supply Removing Center Divider Removing Power Distribution Board Securing Power Distribution Board to Power Supply Cage Reinstalling Center Divider Removing Fixed Power Supply Releasing Center Divider from Power Supply Cage Removing Center Divider from Power Supply Cage Inserting Power Distribution Board in Power Supply Cage TP01997 Reinstalling Hot Swap Power Supply Maintaining Your Server Power Supply Specifications Single Power Supply Input VoltagesSingle Power Supply Output Voltages Technical Reference +3.3 24 a +5.0 +5 V Standby +12.0 48 a System Environmental Specifications Environmental Specifications Equipment Log and Worksheets Equipment Log Equipment Log Calculating Power Usage Current Usage Worksheet, Total Combined Power Used by the Server Product Safety Compliance Regulatory and Compliance InformationProduct Regulatory Compliance Product EMC Compliance Class a Compliance Certifications / Registrations / Declarations Product Regulatory Compliance Markings Electromagnetic Compatibility Notices FCC USA Industry Canada ICES-003 Europe CE Declaration of Conformity Bsmi Taiwan Vcci JapanKorean RRL Compliance Regulated Specified Components Getting Help World Wide Web Telephone Miami Limited Warranty for Intel Chassis Subassembly Products WarrantyExtent of Limited Warranty Warranty Limitations and Exclusions Limitations of Liability Telephone Support How to Obtain Warranty ServiceReturning a Defective Product