Manuals
/
Brands
/
Computer Equipment
/
Network Hardware
/
Juniper Networks
/
Computer Equipment
/
Network Hardware
Juniper Networks
5000 manual
1
1
66
66
Download
66 pages, 3.17 Mb
N
ET
S
CREEN
-5000 S
ERIES
User’s Guide
Version 5.0
P/N 093-1698-000
Rev. D
Contents
Main
Copyright Notice
FCC Statement
Disclaimer
Table of Contents
Page
Page
Page
Preface
GUIDE ORGANIZATION
COMMAND LINE INTERFACE (CLI) CONVENTIONS
JUNIPER NETWORKS NETSCREEN PUBLICATIONS
Overview
NETSCREEN-5000 SERIES
NetScreen-5200
NetScreen-5400
POWER SUPPLIES
NetScreen-5200 Power Recommendations
NetScreen-5400 Power Recommendations
The DC Power Supply
The AC Power Supply
FAN MODULES
NETSCREEN-5000 MODULES
Management Modules
The 5000-M Management Module
The 5000-M2 Management Module
Secure Port Modules
The 5000-8G SPM
The 5000-2G24FE SPM
The 5000-8G2 SPM
The 5000-2XGE SPM
The following table shows the transceivers that are available with the 5000-2XGE SPM.
Page
Installing the Device
GENERAL INSTALLATION GUIDELINES
EQUIPMENT RACK INSTALLATION GUIDELINES
MOUNTING THE NETSCREEN-5000 SERIES
NetScreen-5200 Front and Rear Mount
Page
INSTALLING AND CONNECTING THE AC POWER SUPPLY
INSTALLING AND WIRING A DC POWER SUPPLY
Page
ESTABLISHING AN HA CONNECTION
CONNECTING THE NETSCREEN-5000 SERIES TO A ROUTER
Page
Configuring the Device
OPERATIONAL MODES
Transparent Mode
Route Mode
THE NETSCREEN-5000 INTERFACES
NetScreen-5200 Interfaces
NetScreen-5400 Interfaces
Configurable Interfaces
PERFORMING INITIAL CONNECTION AND CONFIGURATION
Establishing a Terminal Emulator Connection
Upgrading the Firmware During the Boot Process
Changing Your Admin Name and Password
set admin name name_str set admin password pswd_str save
Setting Port and Interface IP Addresses
Viewing Current Interface Settings
Setting the IP Address of the Management Interface
Setting the IP Address for the Trust Zone Interface
Setting the IP Address for the Untrust Zone Interface
CONFIGURING THE DEVICE FOR TELNET AND WEBUI SESSIONS
Starting a Console Session Using Telnet
Starting a Console Session Using Dialup
Establishing a GUI Management Session
10.100.2.183 http://10.100.2.183
CONFIGURING THE CHASSIS ALARM
set chassis audible-alarm string
get chassis
CONFIGURING JUMBO FRAMES
CONFIGURING AGGREGATE INTERFACES
set interface string zone zonename
set interface aggregate1 zone zonename
set interface ethernet2/1 aggregate aggregate1 set interface ethernet2/2 aggregate aggregate1
USING CLI COMMANDS TO RESET THE DEVICE
Page
Servicing the Device
REMOVING AND RESEATING MODULES
REPLACING A DC POWER SUPPLY
REPLACING AN AC POWER SUPPLY
REPLACING THE FAN MODULE
NetScreen-5200 Fan Module
NetScreen-5200 Fan Tray Filter
NetScreen-5400 Fan Module
Page
NetScreen-5400 Fan Tray Filter
CONNECTING AND DISCONNECTING GIGABIT ETHERNET C
REMOVING AND INSTALLING A MINI-GBIC TRANSCEIVER
Page
A
Specifications
NETSCREEN-5200 ATTRIBUTES
NETSCREEN-5400 ATTRIBUTES
ELECTRICAL SPECIFICATION
E
NEBS C
SAFETY CERTIFICATIONS
EMI C
C
The following table shows the 10-Gigabit media types and distances for the different
B
Port Descriptions and LED Status
Appendix B Port Descriptions and LED Status
II Users Guide
MODULE PORT DESCRIPTIONS
The following table describes the ports on the 5000-M and 5000-M2 management modules.
MODULE LED DESCRIPTIONS
Appendix B Port Descriptions and LED Status
IV Users Guide
STATUS LED STATES
This section describes Status LED states on all modules.
Interpreting Status LEDs for the Management Modules
NetScreen-5000 Series V
Interpreting Status LEDs for the Secure Port Module
Interpreting Ethernet Port Status LEDs for All Modules
P OWER SUPPLY LED
Interpreting Power Supply LED Status for the NetScreen-5200
Interpreting Power Supply LED Status for the NetScreen-5400
Single SPM Installed
Page
Page
Index
Numerics
A
C
D
N
P
R
S
T