Juniper Networks 5000 CONFIGURING THE CHASSIS ALARM

Configuring the Chassis Alarm

NetScreen-5000 Series 31

For example, if you assigned the MGT interface an IP address of

10.100.2.183/16, then enter:

http://10.100.2.183

The NetScreen WebUI software displays the login prompt.

3. Enter netscreen in both the Admin Name and Password fields, and then

click Login. (Use lowercase letters only. The Admin Name and Password fields

are both case sensitive.)

The NetScreen WebUI application window appears.

CONFIGURING THE CHASSIS ALARM

The NetScreen-5000 Series system allows you to configure the chassis alarm, an audible

warning that sounds when a system failure or hazardous event occurs. To determine

which failures and events trigger the chassis alarm:

1. Configure the audible alarms by executing the following command:

set chassis audible-alarm string

where string can be any of the following keywords:

2. After configuring the alarm, it is advisable to view alarm environment

information by executing the following command:

get chassis

all Enables all chassis alarms.

battery Sets the chassis alarm to sound when a battery fails.

fan-failed Sets the chassis alarm to sound when a fan fails.

power-failed Sets the chassis alarm to sound when a power supply fails.

temperature Sets the chassis alarm to sound when the temperature goes outside of

the acceptable range.

Contents

Main Copyright Notice FCC Statement Disclaimer Table of Contents Page Page Page Preface GUIDE ORGANIZATION COMMAND LINE INTERFACE (CLI) CONVENTIONS JUNIPER NETWORKS NETSCREEN PUBLICATIONS Overview NETSCREEN-5000 SERIES NetScreen-5200 NetScreen-5400 POWER SUPPLIES NetScreen-5200 Power Recommendations NetScreen-5400 Power Recommendations The DC Power Supply The AC Power Supply FAN MODULES NETSCREEN-5000 MODULES Management Modules The 5000-M Management Module The 5000-M2 Management Module Secure Port Modules The 5000-8G SPM The 5000-2G24FE SPM The 5000-8G2 SPM The 5000-2XGE SPM The following table shows the transceivers that are available with the 5000-2XGE SPM. Page Installing the Device GENERAL INSTALLATION GUIDELINES EQUIPMENT RACK INSTALLATION GUIDELINES MOUNTING THE NETSCREEN-5000 SERIES NetScreen-5200 Front and Rear Mount Page INSTALLING AND CONNECTING THE AC POWER SUPPLY INSTALLING AND WIRING A DC POWER SUPPLY Page ESTABLISHING AN HA CONNECTION CONNECTING THE NETSCREEN-5000 SERIES TO A ROUTER Page Configuring the Device OPERATIONAL MODES Transparent Mode Route Mode THE NETSCREEN-5000 INTERFACES NetScreen-5200 Interfaces NetScreen-5400 Interfaces Configurable Interfaces PERFORMING INITIAL CONNECTION AND CONFIGURATION Establishing a Terminal Emulator Connection Upgrading the Firmware During the Boot Process Changing Your Admin Name and Password set admin name name_str set admin password pswd_str save Setting Port and Interface IP Addresses Viewing Current Interface Settings Setting the IP Address of the Management Interface Setting the IP Address for the Trust Zone Interface Setting the IP Address for the Untrust Zone Interface CONFIGURING THE DEVICE FOR TELNET AND WEBUI SESSIONS Starting a Console Session Using Telnet Starting a Console Session Using Dialup Establishing a GUI Management Session 10.100.2.183 http://10.100.2.183 CONFIGURING THE CHASSIS ALARM set chassis audible-alarm string get chassis CONFIGURING JUMBO FRAMES CONFIGURING AGGREGATE INTERFACES set interface string zone zonename set interface aggregate1 zone zonename set interface ethernet2/1 aggregate aggregate1 set interface ethernet2/2 aggregate aggregate1 USING CLI COMMANDS TO RESET THE DEVICE Page Servicing the Device REMOVING AND RESEATING MODULES REPLACING A DC POWER SUPPLY REPLACING AN AC POWER SUPPLY REPLACING THE FAN MODULE NetScreen-5200 Fan Module NetScreen-5200 Fan Tray Filter NetScreen-5400 Fan Module Page NetScreen-5400 Fan Tray Filter CONNECTING AND DISCONNECTING GIGABIT ETHERNET C REMOVING AND INSTALLING A MINI-GBIC TRANSCEIVER Page A Specifications NETSCREEN-5200 ATTRIBUTES NETSCREEN-5400 ATTRIBUTES ELECTRICAL SPECIFICATION E NEBS C SAFETY CERTIFICATIONS EMI C C The following table shows the 10-Gigabit media types and distances for the different B Port Descriptions and LED Status Appendix B Port Descriptions and LED Status II Users Guide MODULE PORT DESCRIPTIONS The following table describes the ports on the 5000-M and 5000-M2 management modules. MODULE LED DESCRIPTIONS Appendix B Port Descriptions and LED Status IV Users Guide STATUS LED STATES This section describes Status LED states on all modules. Interpreting Status LEDs for the Management Modules NetScreen-5000 Series V Interpreting Status LEDs for the Secure Port Module Interpreting Ethernet Port Status LEDs for All Modules P OWER SUPPLY LED Interpreting Power Supply LED Status for the NetScreen-5200 Interpreting Power Supply LED Status for the NetScreen-5400 Single SPM Installed Page Page Index Numerics A C D N P R S T