Manuals / Brands / Computer Equipment / Network Hardware / Juniper Networks / Computer Equipment / Network Hardware

Juniper Networks 5000 INSTALLING AND CONNECTING THE AC POWER SUPPLY, INSTALLING AND WIRING A DC POWER SUPPLY

1 66

Download 66 pages, 3.17 Mb

Installing and Connecting the AC Power Supply

NetScreen-5000 Series 17

INSTALLING AND CONNECTING THE AC POWER SUPPLY

To install and connect the AC power supply to the NetScreen-5000 Series:

1. On the NetScreen-5200, slide the power supply into one of the power

compartments in the back of the system.

On the NetScreen-5400, slide the power supply into one of the power

compartments on the front of the system.

2. Fasten the power supply to the system by tightening the corner screws into the

eyelets on the sides of the power supply.

3. If you want to install two power supplies in the NetScreen-5200 or three power

supplies in the NetScreen-5400, then repeat steps 1 and 2 for the remaining

power supplies.

4. Connect the female end of a standard power cord to the male connector on the

back of each power supply.

5. Connect each power cord to a standard 100-240-Volt power outlet.

6. Turn the power switches on.

INSTALLING AND WIRING A DC POWER SUPPLY

To install and connect the DC power supply to the NetScreen-5000 Series system:

1. On the NetScreen-5200, slide the power supply into one of the power

compartments in the back of the system.

On the NetScreen-5400, slide the power supply into one of the power

compartments on the front of the system.

2. Fasten the power supply to the system by tightening the corner screws into the

eyelets on the sides of the power supply.

3. If you want to install two power supplies in the NetScreen-5200 or three power

supplies in the NetScreen-5400, then repeat steps 1 and 2 for the remaining

power supplies.

Note: Whenever you deploy two or more power supplies to a

NetScreen-5000 Series system, connect each to a different power source.

Each power supply is intended to receive power from separate feeds.

Note: If there are multiple power supplies in the NetScreen-5000 Series system

and any of them are off, then the Alarm LED on the management module glows

red. This alarm indicates that maximum system stability requires all installed

power supplies to be operational.

Contents

Main Copyright Notice FCC Statement Disclaimer Table of Contents Page Page Page Preface GUIDE ORGANIZATION COMMAND LINE INTERFACE (CLI) CONVENTIONS JUNIPER NETWORKS NETSCREEN PUBLICATIONS Overview NETSCREEN-5000 SERIES NetScreen-5200 NetScreen-5400 POWER SUPPLIES NetScreen-5200 Power Recommendations NetScreen-5400 Power Recommendations The DC Power Supply The AC Power Supply FAN MODULES NETSCREEN-5000 MODULES Management Modules The 5000-M Management Module The 5000-M2 Management Module Secure Port Modules The 5000-8G SPM The 5000-2G24FE SPM The 5000-8G2 SPM The 5000-2XGE SPM The following table shows the transceivers that are available with the 5000-2XGE SPM. Page Installing the Device GENERAL INSTALLATION GUIDELINES EQUIPMENT RACK INSTALLATION GUIDELINES MOUNTING THE NETSCREEN-5000 SERIES NetScreen-5200 Front and Rear Mount Page INSTALLING AND CONNECTING THE AC POWER SUPPLY INSTALLING AND WIRING A DC POWER SUPPLY Page ESTABLISHING AN HA CONNECTION CONNECTING THE NETSCREEN-5000 SERIES TO A ROUTER Page Configuring the Device OPERATIONAL MODES Transparent Mode Route Mode THE NETSCREEN-5000 INTERFACES NetScreen-5200 Interfaces NetScreen-5400 Interfaces Configurable Interfaces PERFORMING INITIAL CONNECTION AND CONFIGURATION Establishing a Terminal Emulator Connection Upgrading the Firmware During the Boot Process Changing Your Admin Name and Password set admin name name_str set admin password pswd_str save Setting Port and Interface IP Addresses Viewing Current Interface Settings Setting the IP Address of the Management Interface Setting the IP Address for the Trust Zone Interface Setting the IP Address for the Untrust Zone Interface CONFIGURING THE DEVICE FOR TELNET AND WEBUI SESSIONS Starting a Console Session Using Telnet Starting a Console Session Using Dialup Establishing a GUI Management Session 10.100.2.183 http://10.100.2.183 CONFIGURING THE CHASSIS ALARM set chassis audible-alarm string get chassis CONFIGURING JUMBO FRAMES CONFIGURING AGGREGATE INTERFACES set interface string zone zonename set interface aggregate1 zone zonename set interface ethernet2/1 aggregate aggregate1 set interface ethernet2/2 aggregate aggregate1 USING CLI COMMANDS TO RESET THE DEVICE Page Servicing the Device REMOVING AND RESEATING MODULES REPLACING A DC POWER SUPPLY REPLACING AN AC POWER SUPPLY REPLACING THE FAN MODULE NetScreen-5200 Fan Module NetScreen-5200 Fan Tray Filter NetScreen-5400 Fan Module Page NetScreen-5400 Fan Tray Filter CONNECTING AND DISCONNECTING GIGABIT ETHERNET C REMOVING AND INSTALLING A MINI-GBIC TRANSCEIVER Page A Specifications NETSCREEN-5200 ATTRIBUTES NETSCREEN-5400 ATTRIBUTES ELECTRICAL SPECIFICATION E NEBS C SAFETY CERTIFICATIONS EMI C C The following table shows the 10-Gigabit media types and distances for the different B Port Descriptions and LED Status Appendix B Port Descriptions and LED Status II Users Guide MODULE PORT DESCRIPTIONS The following table describes the ports on the 5000-M and 5000-M2 management modules. MODULE LED DESCRIPTIONS Appendix B Port Descriptions and LED Status IV Users Guide STATUS LED STATES This section describes Status LED states on all modules. Interpreting Status LEDs for the Management Modules NetScreen-5000 Series V Interpreting Status LEDs for the Secure Port Module Interpreting Ethernet Port Status LEDs for All Modules P OWER SUPPLY LED Interpreting Power Supply LED Status for the NetScreen-5200 Interpreting Power Supply LED Status for the NetScreen-5400 Single SPM Installed Page Page Index Numerics A C D N P R S T