NetScreen-5200, NetScreen-5400 | Juniper Networks 5000 manual

Chapter 1 Overview

NETSCREEN-5000 SERIES

This section describes the NetScreen-5000 Series, which currently includes the NetScreen-5200 and the NetScreen-5400.

NetScreen-5200

The NetScreen-5200 is a chassis-based, two-slot network security device with a 2U (rack unit) chassis. Slot 1 is for the management module and Slot 2 is for the Secure Port Module (SPM). The device has two hot-swappable power supplies for power redundancy and a removable fan module.

The figure below shows a NetScreen-5200 with a management module in slot 1 (top) and an SPM in slot 2 (bottom).

NetScreen-5400

The NetScreen-5400 is a chassis-based, four-slot network security device with a 5U (rack unit) chassis. The top slot (slot 1) holds the management module, and the bottom slots (slots 2-4) hold up to three Secure Port Modules (SPMs) for flexible, high-density port configurations. The device has three hot-swappable power supplies for power redundancy and a removable fan module.

The figure below shows a NetScreen-5400 fully populated with a management module in slot 1 (top) and SPMs in slots 2 through 4.

Management,

slot 1

SPM, slot 2

SPM, slot 3

SPM, slot 4

2	User’s Guide

Image 10

Juniper Networks manual NetScreen-5200, NetScreen-5400, NETSCREEN-5000 Series

Contents

NETSCREEN-5000 Series Copyright Notice Table of Contents Servicing the Device IX-I Table of Contents Preface Guide Organization Command Line Interface CLI Conventions Juniper Networks Netscreen Publications Overview1 NetScreen-5400 NetScreen-5200NETSCREEN-5000 Series NetScreen-5400 Power Recommendations NetScreen-5200 Power RecommendationsPower Supplies DC Power Supply AC Power Supply FAN Modules NETSCREEN-5000 Modules Management Modules 5000-M Management Module 5000-M2 Management Module Secure Port Modules 5000-8G SPM 5000-2G24FE SPM 5000-8G2 SPM 5000-2XGE SPM Part Number Description Distance Fiber Type Overview User’s Guide Installing the Device General Installation Guidelines Equipment Rack Installation Guidelines NetScreen-5200 Front and Rear Mount Mounting the NETSCREEN-5000 Series NetScreen-5200 Mid-Mount NetScreen-5400 Front Mount Installing and Connecting the AC Power Supply Installing and Wiring a DC Power Supply 48V COMThumbscrew Power Connecting the NETSCREEN-5000 Series to a Router or Switch Establishing AN HA Connection Installing the Device User’s Guide Configuring the Device Route Mode Transparent ModeOperational Modes NetScreen-5200 Interfaces NETSCREEN-5000 Interfaces Configurable Interfaces NetScreen-5400 Interfaces Performing Initial Connection and Configuration Establishing a Terminal Emulator Connection Upgrading the Firmware During the Boot Process Viewing Current Interface Settings Changing Your Admin Name and PasswordSetting Port and Interface IP Addresses Setting the IP Address of the Management Interface Setting the IP Address for the Trust Zone Interface Setting the IP Address for the Untrust Zone Interface Configuring the Device for Telnet and Webui Sessions Starting a Console Session Using TelnetAllowing Outbound Traffic Starting a Console Session Using Dialup Establishing a GUI Management Session Configuring the Chassis Alarm Http//10.100.2.183 Configuring Jumbo Frames Configuring Aggregate Interfaces Using CLI Commands to Reset the Device Following CLI command unset admin device-reset Press the y key Following message appears Servicing the Device Replacing a DC Power Supply Removing and Reseating Modules Replacing AN AC Power Supply Replacing the FAN Module NetScreen-5200 Fan Module NetScreen-5200 Fan Tray Filter Remove the fan tray See NetScreen-5200 Fan Module on NetScreen-5400 Fan Module Replacing the Fan Module NetScreen-5400 Fan Tray Filter Remove the fan tray See NetScreen-5400 Fan Module on Connecting and Disconnecting Gigabit Ethernet Cables Removing and Installing a MINI-GBIC Transceiver Servicing the Device User’s Guide Specifications NETSCREEN-5400 Attributes Electrical SpecificationNETSCREEN-5200 Attributes Environmental Nebs Certifications Safety CertificationsConnectors EMI Certifications Appendix a Specifications Port Descriptions and LED Status B Module Port Descriptions MGT Module LED Descriptions Following table details the ports on the 5000-8G2 SPM Interpreting Status LEDs for the Management Modules Status LED States Interpreting Status LEDs for the Secure Port Module Interpreting Ethernet Port Status LEDs for All Modules Power Supply Leds Interpreting Power Supply LED Status for the NetScreen-5200Interpreting Power Supply LED Status for the NetScreen-5400 Single SPM Installed FAN LED Viii Index IX-II