Manuals / Brands / Power Tools / Biscuit Joiner / Juniper Networks / Power Tools / Biscuit Joiner

Juniper Networks C2000, C4000 Removing and Installing a Hard Drive

1 76

Download 76 pages, 1.29 Mb

2. Slide the locking tab (ejector button) to the left to release the module. See

Figure 11 and Figure 12.

3. Hold the tab to the left, and using the handle, slowly pull the power supply module

out.

To install a power supply module:

1. Hold the locking tab (ejector button) to the left, and slowly slide the module into

the chassis until it clicks into place.

2. Insert the power cord into the AC power IEC receptacle.

Figure 11: C2000 Power Supply

Figure 12: C4000 Power Supply

Removing and Installing a Hard Drive

NOTE: If your system is powered on, see the SRC–PE Getting Started User Guide for

commands to run before performing these steps.

To remove a hard drive:

1. Slide the locking tab in the bottom-right corner to the right to release the hard

drive.

2. Hold the tab to the right and slowly pull the unit out.

To install a hard drive, hold the locking tab to the right and slowly slide the unit into

the chassis until it clicks into place.

34 ■Removing and Installing a Hard Drive

C2000 and C4000 1.0.x Hardware Guide

Contents

Main C-series Platforms C2000 and C4000 Hardware Guide Release 1.0.x ii End User License Agreement iii iv Table of Contents Part 1 Product Overview Part 2 Initial Installation Part 3 Hardware Maintenance Procedures and Specifications Page Page About This Guide Objectives Audience Documentation Conventions Table 1 on page x defines the notice icons used in this guide. Table 2 on page x defines text conventions used throughout the documentation. Table 1: Notice Icons Table 2: Text Conventions Related Juniper Networks Documentation Table 3: Juniper Networks C-series and SRC Technical Publications xii Obtaining Documentation Documentation Feedback Requesting Support Page Page Chapter 1 C-series Platform Overview System Description C-series Platform Models Page C-series Model Components Network Management Tools CLI Management Page Page Part 2 Initial Installation Page Chapter 2 Unpacking and Inspecting the C-series Before You Begin Unpacking the Units Inspecting System Components and Accessories If You Detect or Suspect Damage Contacting Juniper Networks Chapter 3 Installing and Cabling the C-series Before You Begin Freestanding Installation Rack-Mounted Installation Installation Guidelines Preparing the Equipment Racks Installing the System Cabling the System Cabling the Management Console Management Ports Cabling Ethernet Interfaces Cabling the System for Power Page Page Chapter 4 Powering Up the C-series Platform Powering Up Status LEDs The LEDs listed in Table 5 on page 20 are used on both models. Table 5: Model LEDs See Setting the Initial Configuration on page 21. 20 Setting the Initial Configuration Configuration Overview Setting Up Management Access and Logging In Configuring the Juniper Networks Database Configuring Hostname and Domain Parameters Configuring the System for Remote Access Configuring the System to Accept SSH and Telnet Connections Adding an Admin User Account See Maintaining the System on page 31. Page Part 3 Hardware Maintenance Procedures and Specifications Page Chapter 6 Maintaining the System Required Tools and Items Storing Modules and Components Cleaning the System Removing and Installing a Fan Removing and Installing a Power Supply Module Removing and Installing a Hard Drive Chapter 7 System Specifications C2000 Model Specifications Table 6: C2000 Model Specifications Table 6: C2000 Model Specifications (continued) C4000 Model Specifications Table 7: C4000 Model Specifications 36 Page Page Chapter 8 Managing RAID Disks on a C-series C-series Platform Data Storage Managing Disks in a C-series Platform Replacing a Disk Reinitializing an Active Disk Viewing Information About Disks on a C-series Platform Table 8: show disk status Output Fields 42 Chapter 9 Installation Guidelines and Requirements Your Preinstallation Responsibilities Environmental Requirements Regulatory Compliances Safety Guidelines Equipment Rack Requirements Mechanical Requirements Space Requirements Proper Rack Installation Cabling Recommendations Product Reclamation and Recycling Program Hardware Compliance Federal Communications Commission (FCC) Statement FCC Requirements for Consumer Products Food and Drug Administration, Center for Devices and Radiological Health Canadian Department of Communications Radio Interference Regulations Rglement sur le brouillage radiolectrique du ministre des communications Industry Canada Notice CS-03 Avis CS-03 d'Industrie Canada D.O.C. Explanatory Notes: Equipment Attachment Limitations Notes explicatives du ministre des Communications: limites visant les accessoires EC Declaration of Conformity Voluntary Control Council for Interference (VCCI) Statement for Japan Chapter 10 Contacting Customer Support and Returning Hardware Contacting Customer Support Return Procedure Locating Component Serial Numbers Information You Might Need to Supply to JTAC Tools and Parts Required Returning Products for Repair or Replacement Packing Instructions for Returning a Chassis Page Chapter 11 Declaration of Conformity Declaration of Conformity Page Page Page Index A C D E N P R S T