Installing a Mini PIM | Juniper Networks SSG 20 specs

8.Grasp the screws on each side of the mini PIM faceplate and slide the mini PIM out of the device. Place the mini PIM in the electrostatic bag or on the antistatic mat.

Figure 16: Removing a Mini PIM

9.If you are not reinstalling a mini PIM into the empty slot, install a blank faceplate over the slot to maintain proper airflow.

Installing a Mini PIM

To install a mini PIM, perform the following steps:

1.Attach an ESD grounding strap to your bare wrist and connect the strap to the ESD point on the chassis or to an outside ESD point if the SSG 20 device is disconnected from earth ground.

2.Unplug the power adapter from the device. Verify that the POWER LED is off.

3.Grasp the screws on each side of the mini PIM faceplate and align the notches in the connector at the rear of the mini PIM with the notches in the mini PIM slot in the SSG 20 device. Then slide the mini PIM in until it lodges firmly in the device.

Figure 17: Installing a Mini PIM

CAUTION: Slide the mini PIM straight into the slot to avoid damaging the components on the mini PIM.

4.Tighten the screws on each side of the mini PIM faceplate using a 1/8-inch slotted screwdriver.

5.Insert the appropriate cables into the cable connectors on the mini PIM.

Replacing a Mini-Physical Interface Module 53

Image 53

Juniper Networks SSG 20 manual Installing a Mini PIM, Removing a Mini PIM

Contents

SSG 20 Hardware Installation and Configuration Guide Copyright Notice Table of Contents Appendix B Initial Configuration Wizard About This Guide WebUI Conventions Organization CLI Conventions Navigational Path and Configuration Settings Obtaining Documentation and Technical Support Hardware Overview Port and Power Connectors Status LED Descriptions Name Color Front PanelSystem Status LEDs Name Color Status Description LAN Port LEDs Name Color Status Description Port DescriptionsLink TX/RX Mini PIMs for the SSG Mini Physical Interface Module Port Descriptions Mini PIM LED States on the SSG Type Name Color Description Radio Transceivers Power AdapterBack Panel Grounding Lug USB Port Antennae Types Installing and Connecting the Device Before You Begin Installing Equipment SSG 20 Front-mount Connecting the Power Connecting Interface Cables to a Device Connecting a Device to an Untrusted Network Connecting a Device to a Network Serial AUX/Console Ports Connecting Mini PIMs to an Untrusted Network Microfilter and Splitter on Your Network Connection Connecting a Device to an Internal Network or a Workstation Wireless Antennae Configuring the Device Using a Console Connection Accessing a Device Using the WebUI WebUI Login Prompt Using Telnet DMZ Default Device SettingsDefault Physical Interface to Zone Bindings Port Label Interface Zone Wireless and Logical Interface Bindings Root Admin Name and Password Basic Device Configuration Bridge Group Interfaces Date and Time Management Services Administrative Access Management Interface Address Default RouteHostname and Domain Name Basic Wireless Configuration Backup Untrust Interface Configuration Default SSG 20-WLAN Configuration WPA-PSK Wireless Authentication and Encryption OptionsWPA WPA2-PSK Activate wireless changes ADSL2/2+ Interface Mini PIM Configuration Virtual Circuits PPPoE or PPPoA Static IP Address and Netmask T1 Interface Isdn Interface E1 Interface Modem Interface Verifying External Connectivity Basic Firewall Protections Resetting a Device to Factory Defaults Page Replacing a Mini-Physical Interface Module Servicing the DeviceRequired Tools and Parts Removing a Mini PIM Removing a Blank Faceplate Removing a Mini PIM Installing a Mini PIM Bottom of Device Upgrading Memory Unlocking the Memory Module 56 „ Upgrading Memory Specifications Environmental Tolerance PhysicalElectrical Certifications SafetyEMC Emissions EMC Immunity RJ-45 Connector Pinouts Name Description ConnectorsGND DSR DCD DB-9 Connector Pinouts Name DescriptionDTR RTSPage Initial Configuration Wizard Rapid Deployment Window Administrator Login Window Physical Interface Window Wlan Access Point Window ADSL2/2+ Interface Window Adsl Interface Configuration Window VPI/VCI Fields in Adsl Interface Configuration Window Description T1 Physical Layer Tab Window T1 Interface Windows Fields in T1 Physical Layer Tab Window Description 70 „ Page Cisco Hdlc Option with Cisco Hdlc Tab Window E1 Physical Layer Tab Window E1 Interface Windows Fields in E1 Physical Layer Tab Window Description Field Description Isdn Interface Windows SPID2 Fields in Isdn Physical Layer Tab Window DescriptionSPID1 Page Eth0/0 Interface Untrust Zone Window 92 Modem Interface Window Eth0/1 Interface DMZ Zone Window Bgroup0 Interface Window Bgroup0 Interface Trust Zone Window Fields in Bgroup0 Interface Window Description Wireless0/0 Interface Trust Zone Window Ssid Fields in Wireless0/0 Interface Window DescriptionInterface Summary Window Physical Ethernet Dhcp Interface Window Wireless Dhcp Interface Window Confirmation Window Confirmation Window Adsl Index VPI/VCI