Connecting to Various Devices
Signals that Can Be Input to the Projector
The following signals can be input to the projector through the corresponding VICs (Video Input Cards).
•Before connection, be sure to turn off the projector and devices.
•Read the manual which comes with each device thoroughly.
■Analog RGB signals
The signals with the following resolutions can be input to the input terminal of the RGB Analog VIC.
Screen resolution | Horizontal | Vertical |
| Effective number of |
| ||||
(standard name) | frequency | frequency |
| scanning line |
|
|
|
|
|
DTV (480p 31.5kHz) | 31.5Hz | 59.9Hz |
| 483 |
|
|
|
|
|
DTV (720p 60Hz) | 45.0kHz | 60.0Hz |
| 720 |
|
|
|
|
|
DTV (1080p 60Hz) | 67.5kHz | 60.0Hz |
| 1080 |
|
|
|
|
|
VGA (640 X 480 60Hz) | 31.5kHz | 59.9Hz |
| 480 |
|
|
|
|
|
VGA (640 X 480 75Hz) | 37.5kHz | 75.0Hz |
| 480 |
|
|
|
|
|
VGA (640 X 480 85Hz) | 43.3kHz | 85.0Hz |
| 480 |
|
|
|
|
|
VGA (640 X 480 Macintosh 13") | 35.0kHz | 66.7Hz |
| 480 |
|
|
|
|
|
SVGA (800 X 600 85Hz) | 53.7kHz | 85.0Hz |
| 600 |
|
|
|
|
|
SVGA (832 X 624 Macintosh 16") | 49.8kHz | 74.6Hz |
| 624 |
|
|
|
|
|
XGA (1024 X 768 60Hz) | 48.4kHz | 60.0Hz |
| 768 |
|
|
|
|
|
XGA (1024 X 768 70Hz) | 56.5kHz | 70.1Hz |
| 768 |
|
|
|
|
|
XGA (1024 X 768 75Hz) | 60.0kHz | 75.0Hz |
| 768 |
|
|
|
|
|
XGA (1024 X 768 85Hz) | 68.7kHz | 85.0Hz |
| 768 |
|
|
|
|
|
XGA (1024 X 768 Macintosh 19") | 60.2kHz | 74.9Hz |
| 768 |
|
|
|
|
|
XGA (1024 X 768 Macintosh 21") | 68.7kHz | 75.1Hz |
| 870 |
|
|
|
|
|
SXGA (1280 X 1024 60Hz) | 63.9kHz | 60.0Hz |
| 1024 |
|
|
|
|
|
SXGA (1280 X 1024 67Hz) | 70.8kHz | 67.0Hz |
| 1024 |
|
|
|
|
|
SXGA (1280 X 1024 75Hz) | 79.9kHz | 75.0Hz |
| 1024 |
|
|
|
|
|
SXGA (1280 X 1024 76Hz) | 81.2kHz | 76.2Hz |
| 1024 |
|
|
|
|
|
SXGA (1280 X 1024 85Hz) | 91.1kHz | 85.0Hz |
| 1024 |
|
|
|
|
|
UXGA (1600 X 1200 60Hz) | 75.0kHz | 60.0Hz |
| 1200 |
|
|
|
|
|
UXGA (1600 X 1200 65Hz) | 81.2kHz | 65.0Hz |
| 1200 |
|
|
|
|
|
UXGA (1600 X 1200 70Hz) | 87.5kHz | 70.0Hz |
| 1200 |
|
|
|
|
|
UXGA (1600 X 1200 75Hz) | 93.8kHz | 75.0Hz |
| 1200 |
|
|
|
|
|
UXGA (1600 X 1200 85Hz) | 106.3kHz | 85.0Hz |
| 1200 |
|
|
|
|
|
QXGA (2048 X 1536 60Hz) | 95.3kHz | 59.9Hz |
| 1536 |
|
|
|
|
|
QXGA (2048 X 1536 60Hz) | 95.7kHz | 60.0Hz |
| 1536 |
|
|
|
|
|
ENGLISH
•The RGB signals whose dot (pixel) clock is lower than 25 MHz or over 280 MHz are not available.
•The SVGA signals whose dot (pixel) clock is lower than 50 MHz are not available.
•When you want to input NTSC signal, make the signal twice as dense by a line doubler.
•The resolution and the scanning frequencies are within the range specified in the table on this page.
Be sure that the resolution and the scanning frequencies of the video signal are within the range. A video signal out of the range cannot be used. (Even signals out of the range could be projected. However, it may not be sharp enough. On the other hand, even some of the signals within the range may require adjustment depending on the video board used.)
When a signal other than listed in the table on this page is input, the image could be partially erased or an unneeded fold- over image could appear.
Even signals within the frequency range may not be displayed normally depending on the type of the signal. Composite sync (CS) and G on Sync signals cannot be handled depending on the devices connected.
■Analog HD signals
The HDTV interlaced signals can be input to the input terminal of the Analog HD VIC. NTSC is not available.
■Digital HD signals
The digital HD signals can be input to the input terminal of the
25
