JVC GY-DV550 instruction manual  Alarm Message Display, C D E,  Time/Date Display, 2930

Note:

When the RS-232C cable is connected, the VCR operation mode may not be displayed correctly.

2. CONTROLS, INDICATORS AND CONNECTORS

2-10 Indications in Viewfinder (Cont'd)

● Status 1 In addition to the information on the Status 0 screen, this screen displays audio indicators and information on remaining tape, voltage and lens F-number (or FILTER POSITION).

2. CONTROLS, INDICATORS AND CONNECTORS

2-10 Indications in Viewfinder (Cont'd)

Alarm Message Display

ACCU - FOCUS

G

Display position 8

9

Display

(Example) CH1- - - - + - - CH2- - - - + - - STBY SAVE STOP REC FF

Function

Shows the input level of the audio input channel.

Display ON/OFF can be selected using the VF DISPLAY menu screen.

☞See "AUDIO DISPLAY" on page 78.

VCR in standby mode

VCR in save mode

VCR in stop mode

VCR in record mode

VCR in fast-forward mode

			F
	Alarm message display 1
	Alarm message display 2		I
			B
	CH1 - - -	- - + - -
F 5 . 6	CH2 - - -	- - + - -
STBY	<	6 0	1 2 . 4V

The following alarm messages are displayed on the status 0 and status 1 screens. Event display is not made when an alarm message is displayed in alarm message display 2.

0

A B

REW EJECT (Example)

<60

(Example) 12: 34: 56: 20

(Example) 12.4V

F-number: OPEN, F2, F2.8, F4, F5.6, F8, F11, F16, CLOSE FILTER:

VCR in rewind mode

VCR in eject mode

Remaining tape indication (displayed in 1-minute steps)

When the tape is used for a long time, the remaining tape may not be indicated accurately. At the beginning of the tape, in particular, the indication may show smaller value than the actual one.

Time code display Time code display is available when the "REC TIME" item on the VF DISPLAY menu screen is set to TIME CODE.

☞See "REC TIME" on page 78.

Voltage indication (displayed in 0.1 V steps) The indicator flashes when the battery is low. The indicator will not appear when the camera remote control unit is connected. The F-number of the connected lens or the filter position of the unit is displayed. Whether to display the F-number or filter position, or no display is selected in F. NO/FILTER of the VF DISPLAY screen.

•The F-number may not be displayed depending on the lens type or when the lens is removed. ☞ See page 78

	Indication	Contents
	CLOSE CASSETTE COVER	The cassette cover is not closed.
	VTR WARNING [HEAD]	Head clogging
1	VTR WARNING [SERVO]	Servo error
	VTR WARNING [DEW]	Condensation
	VTR WARNING [HARD]	Hardware error
	VTR WARNING [STOP]	Operation stopped
	VTR WARNING [REW]	Rewinding abnormality
	TAPE NEAR END	Remaining tape time is less than about 2 minutes in the record mode
	TAPE END	Tape end reached
2		REC INHIBITAn unrecordable videocassette (the switch on the back of the cassette is
		set to SAVE) is inserted.
	NO TAPE	VTR trigger is pressed with no tape loaded.

C

D

E

FIL1, FIL2, FIL3 (Example) M: 099

EXT, INT, PARA

REC2

Not displayed during external video signal input or IEEE1394 input.

In the Super Scene Finder (S.S.F.) mode, the number of memorized scenes is shown. M : In MARK mode C : In CUE mode Number: Number of memorized scenes Displays whether the main unit is used for recording or the external VCR connected to the VTR/RM multi-pin connector. The displays will differ depending on the VTR SELECT switch setting. INT is constantly displayed during external video input or IEEE1394 input. INT is constantly displayed when the VTR/RM switch is set to RM.

The display will light during external VCR recording. The display flashes when there is a warning on the external VCR. The display will not appear when the VTR/RM switch is set to RM.

Time/Date Display

		Time/date display
2 0 0 0 /	0 6	/ 1 5	ACCU - FOCUS
2 0 :15:15
					G
					F
					I
REC2					SD
		CH1 - - -	- - + - -		B
EXT				C :	12 3
F 5 . 6		CH2 - - -	- - + - -
STBY		>	6 0	1 2 . 4V

When setting DISPLAY item of the TIME DATE menu screen to ON, the time and date will appear as shown in the diagram on the left. The time and date are recorded on tape during recording as well. For the display formats of the time and date, ☞ see page 84. For setting the time and date, see page 43.

● Status 2 ... Not displayed during external video signal input or IEEE1394 input.
This screen displays the camera setup statuses.
Event display is not available while this screen is displayed.
Indication	Indication Contents
SCENE FILE	A, B, OFF
WHITE BAL	A, B, PRESET, FAW, MANUAL (When remote control unit w/manual balance is connected.)
FILTER	3.2K, 5.6K+1/8ND, 5.6K+1/64ND
SHUTTER	OFF, 1/100 (U)/1/120(E), 1/250, 1/500, 1/1000, 1/2000, 1/60.1 (U)/1/50.1 (E) to 1/2084.6 (U)/
	1/2067.8 (E) (in VARIABLE mode), EEI (in ALC mode)
GAIN	-3dB, 0dB, 3dB, 6dB, 9dB, 12dB, 18dB, LOLUX, ALC
IRIS LEVEL	NORMAL, BACK L, SPOT L
FULL AUTO	ON, OFF
REC TIME	Remaining tape time or time code.

2930