
4. POWER SUPPLY
4-2 Battery Pack Operation (Cont'd)
USING AN ANTON-BAUER BATTERY PACK
4. POWER SUPPLY
To use an
•Battery holder:
Detaching the Battery Case From the
WARNING indicator
| Remaining battery | ||
| power indication | ||
TALLY | E | BATT | F |
|
|
| |
lamp |
|
|
|
| E | BATT |
|
To display the remaining battery power accurately, set the VCR Setup Menu item No. 396 BATTERY TYPE according to the type of the battery pack in use.
☞See page 75.
The status of the remaining battery power can be checked by the remaining battery power indication.
☞See page 24.
When the remaining battery power is nearly exhausted, the |
following warning messages will appear. In this case, replace |
| 2. |
| 1. Black screw A |
1. Remove the two black screws A on the battery case. | |
2. | Remove the lower half of the battery case cover in the |
| downward direction. |
Connector
Compartment
5.
| Viewfinder |
| LOW BATTERY |
BATT lamp | REC |
BATT ALARM |
with a fully charged battery as soon as possible.
●Remaining battery power indication:
Segment bar and "BATT" indicator start to blink
●WARNING indicator and TALLY lamp blink
●Viewfinder:
•BATT lamp lights.
•TALL lamp blinks.
•During status 1 mode, the voltage display flashes.
●Alarm sound beeps
3. | Mount screw B |
| 3. Connector |
5. | 4. |
| |
| Battery holder |
4. Connect the connectors protruding from the |
After the remaining battery power warnings appear, the
3. | Mount screw |
| B |
the connectors on the battery holder. |
*Following connection of the connectors, insert them into the connector compartment.
5. | Secure the battery holder to the |
| mount screws provided with the battery holder. |
Operating Time with Battery Pack | |
When the | |
charged battery pack is attached, the approximate continuous | |
operating time is as follows: | |
Battery Pack | Continuous Operating Time (at 25 ˚C) |
● Battery operating time may differ depending on the number |
of times the battery has been charged, charging conditions |
and the operating environment, etc. Use the values in the |
table on the left for approximate reference times. |
● Operating time is reduced in areas with a cold environment. |
3. To remove the battery case, remove the four screws B fixing | * Take | care | not | to pinch the wires. This could result in | |
the battery case and the connector connecting the battery | |||||
damage. |
|
| |||
case to this unit. |
|
| |||
|
|
|
|
Attaching and Detaching an Anton-Bauer Battery Pack
| 60 minutes |
Magnum 14 | 130 minutes |
80 minutes |
● Operating time is reduced when the power zoom lens is used |
frequently. |
Guide pins |
PRECAUTIONS FOR THE BATTERY PACK
Release lever
Cassette cover |
| |
side panel | Battery | |
Guide holes | pack | |
(x3) | ||
(Trimpack) | ||
|
Release lever
Attaching the Battery Pack | |
1. Align the 3 guide pins of the battery pack with | |
| the guide holes on the battery holder, and push |
| straight to insert the battery pack. |
| The battery cannot be attached properly if the |
| guide pins are not inserted straight. |
2. | Slide the battery pack toward the side panel |
| where the cassette cover is located until it clicks. |
| Now the battery pack has been attached. |
Detaching the Battery Pack |
●When the battery pack is not in use, it must be stored in a cool, dry place.
Do not leave the battery pack in a place where it might be subject to a high temperature (under direct sunlight in a car, etc.), this could cause leakage of the fluid or shorten service life.
●When the terminal section of the battery pack gets dirty, the operating time will be shortened.
●If the operating time becomes greatly reduced even immediately after recharging, the service life of the battery pack is nearly finished. Purchase a new battery pack.
Recharging
●Recharge the battery pack after completely discharging it. Repeated recharging with residual charge remaining could result in reduced battery capacity.
●If the battery capacity is reduced by repeating incomplete recharging, or recharging without discharging, once discharge the battery pack completely, then recharge it to restore the battery capacity.
●If the battery pack is recharged with its internal temperature raised immediately after use, recharging may not be performed completely.
Side panel with display
Battery
While pushing and holding the release lever, slide the battery pack toward the side panel where the LCD display is located, then pull the battery pack outward to remove.
39 | 40 |