| 13. FEATURES OF THE CAMERA SECTION |
| Connecting the Local Remote Control Unit |
13. FEATURES OF THE CAMERA SECTION
PUSH
DV CAMCORDER
Y/C OUT | LINE OUT |
|
|
|
|
|
|
|
| |||||
LP55 | UNIT |
|
|
|
|
|
|
|
|
|
|
|
RM- | REMOTE CONTROL | 1FUNC FUNC 2 | ENTER | 2 | SHUTTER | FOCUS | FAR | ZOOM | TELE | IRIS | AUTO/MANU | IRIS |
MENU | FILE | NEAR | WIDE | PAINTWHITE | BLACKMASTER | |||||||
|
|
|
| /SET |
|
|
|
|
|
|
|
|
|
|
|
| FUNC | GAIN |
|
|
|
|
|
|
|
|
|
|
| FUNC 1 | W.BAL |
|
|
|
|
|
|
|
BACK TALLY lamp
1.
MODE switch
VTR/RM connector
Headset
Camera remote control unit
REMOTE
It is possible to set the switch functions of the camera section using the local remote control unit
Memo:
• | If the switch functions for this unit and the local remote |
| control unit are the same, the switch function of the local |
|
| AUDIO IN | |
4. INCOM MIC | 3. INCOM MIC | INTERCOM | |
switch | |||
switch | connector | ||
2. POWER switch | |||
| Headset |
Connection
Connect the local remote control unit cable to the REMOTE connector of this unit.
Settings
●Set VTR Setup menu No. 050 REMOTE SELECT of this unit to LOCAL.
●When also using the DV terminal, set VTR Setup menu No. 050 REMOTE SELECT to IEEE1394.
CAUTION: When setting VTR Setup menu No. 050 REMOTE SELECT to IEEE1394 + RS232C, the local remote control unit will be inoperable.
Operation
When the OPERATE switch of the local remote control unit is set to ON, the local remote control unit will be operable.
■Unavailable functions
The following functions are unavailable from the local remote control unit.
•
ZOOM FOCUS
SC COARSE SC FINE
H PHASE GAMMA TITLE TITLE SET
•
SC COARSE SC FINE
H PHASE
| remote control unit will have priority. |
• | The IRIS AUTO/MANUAL setting will be the local remote |
| control unit switch setting regardless of the lens section |
| switch setting. |
• | H. PHASE, SC COARSE and SC FINE cannot be |
| adjusted using the local remote control unit. |
• | When |
| displayed on |
| displayed on this unit. |
The unit can be remotely controlled using the camera remote control unit. Use the following available products.
Camera remote control unit
•
|
| (Not available for |
CAUTION: |
| |
To use the camera remote control unit | ||
adjustments of the | ||
mandatory that you contact the nearest | ||
service agent for inquiry about the adjustments. | ||
• | ............... | Cable length is 200m only. |
Intercom headset |
| |
• |
|
|
Connection
● Connect the camera remote control unit to the VTR/RM
Settings 1. Set the MODE switch to RM.
2. Select the power source of this unit using the POWER switch. When supplying power from the power supply of the camera remote control unit through the VTR/RM
3. Set the INCOM MIC setting switch according to the intercom headset microphone type
4. Use the INCOM MIC switch to set whether to use the microphone of the intercom headset.
•The microphone of the headset will become available for use when setting to ON and the volume can be adjusted by turning the volume knob.
5. | Composite video signals of the camera are constantly |
| outputted from the VTR/RM |
| this signal, another type of video signals can be outputted. |
| The output signal is selected in 26 PIN OUT of the Camera |
| SETUP menu screen. |
| (Y/C, RGB or component video signal) |
| Memo: |
•External input video signals will not be outputted from the VTR/RM
•Playback video of the VCR will not be outputted from the VTR/RM
•Call signals will be sent to the operator of the camera remote control unit while the CALL button is held down. During this time, the BACK TALLY lamp will blink. The BACK TALLY lamp will blink when the call signal is received.
•The screen will distort when inputting sync signals to both the main unit and camera remote control unit.
•When the power is set to ON during input of external synchronous signals, the screen may shift vertically for a few seconds; however, this is not a malfunction of the unit.
•Read the instruction manual of the camera remote control unit for the correct usage.
93 | 94 |
