OTHERS
Warnings and Responses (Cont’d)
Error code
Warning |
•Warning Indications for VTR Abnormalities
Should malfunctions occur during VTR operation, this device
Error Code | Error Details | This device Operation | Remedy |
0201 | Indicates dew formation (condensa- | Operation stops. All opera- | Leave this device with the power ON, |
CONDENSATION ON DRUM | tion). | tions are rejected. | until the indication disappears. |
|
|
| X See page 9. |
3200 | Tape cannot be loaded. |
| Switch the power OFF and then switch |
LOADING FAILURE |
|
| it back ON. However, the tape may be |
3300 | Tape cannot be unloaded. |
| damaged depending on the circum- |
UNLOADING FAILURE |
|
| stances. Please consult the person in |
|
|
| charge of professional video equip- |
4100 | Irregularity with eject operation. |
| |
| ment at your nearest | ||
CASSETTE EJECT FAILURE |
|
| |
|
| service agent. | |
|
|
| |
5605 - 5609 | Tape is cut. | Operation stops. | Press the EJECT button to take out the |
DEFECTIVE TAPE |
|
| cassette. |
|
|
| If the tape runs out during recording, |
|
|
| switch the power OFF and then switch |
|
|
| it back ON, press the EJECT button, |
|
|
| and then take out the cassette. |
5702 | Tape end sensor error. | Operation stops. All opera- | Switch the power OFF and then switch |
TAPE END DET. ERROR |
| tions are rejected. | it back ON. However, the tape may be |
5802 | Tape beginning sensor error. |
| damaged depending on the circum- |
TAPE BEGIN DET. ERROR |
|
| stances. Please consult the person in |
|
|
| charge of professional video equip- |
7001 | Drum rotation error. |
| |
| ment at your nearest | ||
DRUM MOTOR FAILURE |
|
| |
|
| service agent. | |
7101 | Capstan rotation error. |
| |
|
| ||
CAP MOTOR FAILURE |
|
|
|
7202 - 7203 | Supply reel rotation error. |
|
|
SUPPLY REEL FAILURE |
|
|
|
7302 - 7303 | Take up reel rotation error. |
|
|
TAKE UP REEL FAILURE |
|
|
|
7305 | Take up reel rotation error when un- |
|
|
TAKE UP REEL FAILURE | loading. |
|
|
8000 | Tape problem detected. |
|
|
EMERGENCY TAPE! |
|
|
|
TURN POWER OFF. | System error when power is turned on. | HDV/DV LED, VTR indicator | Turn off the power and let this device |
TURN BACK ON LATER. |
| and TALLY lamp flash. Only | sit for sometime before turning it back |
|
| POWER switch operation is | on. |
|
| accepted. |
|
TALLY lamp
Blinks when remaining battery power or tape is low. (Only in Camera mode)
Blinking Pattern | Remaining Battery/Tape |
Slow blinking | • Remaining battery power is low. |
(once per sec.) | • Remaining tape time is equivalent to less |
| than 3 minutes. |
Fast blinking | • Tape has run out. |
(four times per sec.) | • Irregularity has occurred in the VTR. |
Alarm Sound
When remaining battery power becomes low, a warning sound is output from the monitoring loudspeaker and the PHONES jack.
(In Camera mode only)
When an irregularity occurs in the VTR, a warning sound is also output.
Whether or not alarm sound should be output and the vol- ume level are selected with the ALARM VR LEVEL item on the OTHERS[1/2] menu screen.
Depending on the alarm conditions, the warning indicators on the LCD monitor/viewfinder screen, the TALLY lamp, and alarm sounds appear as shown in the following table.
Alarm Indications on LCD Monitor/ | TALLY lamp | Alarm Sound | Condition | ||
Viewfinder Screen | |||||
|
|
| |||
VTR alarm indication |
|
|
| Dew formation (condensation) or error has oc- | |
(Example) |
| I |
| curred in the VTR. | |
|
|
|
| ||
|
| J |
| About 3 min. before tape end | |
|
|
| (displayed during recording). | ||
|
| I |
| Tape end | |
|
|
| (displayed during recording). | ||
|
| J |
| Remaining battery power is low. | |
|
|
|
| ||
Display symbols | J : Blinking once per second. | I | : Blinking four times per second. | ||
| : Sound interrupted once per second. | : Continuous sound. | |||
104 | 105 |
