JVC GY-HD200U, GY-HD200E, GY-HD200CHU, GY-HD201E, GY-HD201CHE, GY-HD200CHE Left Side Section, Rca

CONTROLS, INDICATORS AND CONNECTORS

Left Side Section	4[INPUT1/INPUT2] INPUT1/INPUT2 audio input connec-
	tors
	These are audio input connectors for connecting to an
	external audio device or microphone.

c d e

g[GENLOCK/AUX IN] GENLOCK/AUX IN terminal (BNC)

•Input synchronization signals in this terminal when externally synchronizing camera images or playback images.

		•	Set the [AUDIO INPUT] switch 3 according to the
			device to be connected.
		•	Set the CH-2 audio input connector using the [CH-2
9 8 7			INPUT] switch 2.
			The CH-2 audio from the set connector is recorded.
	1	5Shoulder pad slide button
VIDEO		Button to adjust the position of the shoulder pad.
OUT-CH1	2	When you press this button, you can move the position of
CH2-AUDIO	3	the shoulder pad 6 forward or backward.
		6Shoulder pad
1394
IEEE		7Cassette cover
		Sliding the EJECT switch a on page 18 located on the
		top section opens this cover to allow insertion or removal

g

h

f

b

VIDEO
-CH1	i
CH2-AUDIO OUT
	j
1394	k
IEEE

a

Synchronization signal: BB (Black Burst) signal of SD or Tri sync signal of HD

•Input composite video signals to record images from an external device with this device.

•Select the signal to input with the [GENLOCK/AUX IN]

switch c.

X See “Using GENLOCK Functions” on page 66.

X See “Recording Composite Video Signals from an External Device” on page 65.

h[HD/SD-SDI] HD/SD-SDI output terminal (BNC) Outputs HD/SD-SDI (Serial Digital Interface) signals. Out- puts embedded audio signals as digital audio.

The sampling frequency for embedded audio is 48 kHz.

0				of the videocassette.
	6	5	4
				CAUTION
1Viewfinder connector (6-pin)
				To prevent foreign objects from entering the internal parts of
Connect the cable from the viewfinder here.
				the VTR unit, do not leave this device with the cover open
• Set the image format for this terminal in VF SIGNAL on
				for extended periods of time.
the LCD/VF[4/4] menu screen. X See page 92.
2[CH-2 INPUT] CH-2		audio input	connector selector	8[VIDEO OUT] Video output terminal (RCA)
switch
				This is a terminal for composite video signal output.
Selects the CH-2 audio input connector.
				• Select whether or not to output a signal with setup in
INPUT1	: Inputs the audio from the INPUT1 connector
				SET UP on the VIDEO FORMAT[2/2] menu screen.
INPUT2	4 into CH-2.			(Only for U model)
	: Inputs the audio from the INPUT2 connector			9[AUDIO OUTPUT CH-1/CH-2] Audio output connector
	4 into CH-2.
				(RCA)
MEMO				Output connector for audio signals.
				• Outputs the input audio signal in the Camera mode.
The audio from the INPUT1 connector is also input into
				• Outputs the playback audio signal in the VTR mode.
CH-1 regardless of the setting.
				• When a HDV/DV signal (IEEE1394) is input, the EE
3[AUDIO INPUT] Audio input signal selector switch				sound of the input audio signal is output in the VTR
				mode.
This switch is used to select the input sound signal from
INPUT1 or INPUT2 connector.				MEMO
LINE	: Set to this position when connected to audio			Alarm sound is not output.
	equipment, etc. The reference input level is
	+4 dBs.			0[IEEE1394] IEEE1394 connector (6-pin)
MIC	: Set to this position when the dynamic micro-			Using an IEEE1394 cable (optional), a digital video com-
	phone is connected.			ponent with IEEE1394 connector can be connected here.
MIC+48V : Set to this position			when a microphone	X See “Connecting the IEEE1394 Cable” on page 64.
	requiring +48 V power supply (phantom			X See “HDV/DV Dubbing” on page 68.
	microphone, etc.) is connected.			CAUTION
CAUTION
				When connecting the IEEE1394 cable, confirm that the
When connecting a component that does not require +48 V
				connector is facing the right direction before inserting.
power supply, make sure that the switch is not set to				X See page 64.
MIC+48V before the component is connected.
				MEMO
MEMO
				Put the covers on the connectors when you are not using
You can select the normal input level for MIC and MIC+48V
				them.
in the INPUT1, 2 MIC REF. item on the AUDIO/MIC[1/2]

menu screen. X See page 87.

a[STUDIO] Studio terminal (Round 10-pin)

Connect the studio cable from the KA-HD250 Studio Kit (sold separately). Connect the KA-HD250 to use this device as a studio camera.

For details, refer to the KA-HD250 INSTRUCTION MAN- UAL.

b[DC INPUT] DC input terminal (XLR 4-pin)

This is the 12V DC power input terminal. Connect to the AC adapter.

When a battery is installed and a cable is connected to this terminal, power supply from the battery stops and power is supplied by this terminal.

c[GENLOCK/AUX IN] GENLOCK/AUX IN switch

Set according to the signal input in the [GENLOCK/AUX IN] terminal.

GENLOCK : Set to this when inputting external synchroni- zation signals.

AUX IN : Set to this when inputting composite video

signals from an external device.

MEMO

If no signals are input to the [AUX IN] terminal and this switch is set to AUX IN, the monitor turns black and video is not output from any terminal.

d[PBPR/TC] PBPR/Time code switch

Set according to the [PB/TC IN] and [PR/TC OUT] terminal signals.

PBPR : Set to this when outputting component PB signals from the [PB/TC IN] terminal and outputting com- ponent PR signals from the [PR/TC OUT] terminal.

TC : Set to this when inputting LTC time code from the [PB/TC IN] terminal and outputting the built-in time code generator from the [PR/TC OUT] terminal.

MEMO

When this switch is set to TC, video is not output from the Y/PB/PR terminal (i j k).

e[IEEE1394] IEEE1394 switch

Set according to the image format of the input/output sig- nal and playback signal of the IEEE1394 terminal.

HDV	: Set to this for HDV format.
DV	: Set to this for DV format.

f[REMOTE] REMOTE terminal (Round 6-pin)

Some functions of this camera can be controlled exter- nally.

Connect to a remote control unit (RM-LP55/RM-LP57). X See “Connect a Remote Control Unit (RM-LP55/RM- LP57)” on page 71.

In addition, the time code for the built-in time code genera- tor and playback time code are output.

X See pages 20 and 21 for the signals that are enabled.

MEMO

Set whether or not to output SDI signals from this terminal in HD/SD-SDI OUT of the VIDEO FORMAT[2/2] menu screen.

i[Y] Component Y signal output terminal (BNC) Outputs Y signal of component when the [PBPR/TC] switch

dis set to PBPR.

j[PB/TC IN] Component PB signal output/time code input terminal (BNC)

•Outputs PB signal of component when the [PBPR/TC] switch d is set to PBPR.

•Inputs time code when the [PBPR/TC] switch d is set to TC. Enter the LTC time code to slave lock this device’s time code generator with an external time code genera- tor.

MEMO

Set TCG SOURCE on the TC/UB/CLOCK Menu screen to EXTERNAL to input external time codes.

X See “Synchronizing with an External Time Code Gener- ator” on page 49.

k[PB/TC OUT] Component PB signal output/time code output terminal (BNC)

•Outputs PR signal of component when the [PBPR/TC] switch d is set to PBPR.

•Outputs the LTC time code of the built-in time code gen- erator when the [PBPR/TC] switch d is set to TC.

MEMO

Set the [Y/PB/PR] terminal (i j k) output image signal to RGB or Y/C video signals in OUTPUT TERM. [DV] on the VIDEO FORMAT[2/2] menu screen. (Only for DV format)

X See “OUTPUT TERM. [DV]” on page 79.

16 17