Recording specification | JVC HM-DR10000EU specification

82EN

SPECIFICATIONS

GENERAL

Power requirement	: AC 220 – 240 V`, 50/60 Hz
Power consumption
Power on	:	36 W
Power off	:	8.7 W
Temperature
Operating	: 5°C to 40°C
Storage	: –20°C to 60°C
Operating position	: Horizontal only
Dimensions (WxHxD) :		468 x 145 x 369 mm
Weight	:	8.0 kg
Maximum recording time
D-VHS (STD)	:	420 min. with DF-420 video
		cassette
D-VHS (LS3)	:	1260 min. with DF-420 video
		cassette
S-VHS/VHS (SP)	:	240 min. with E-240 video
		cassette
S-VHS/VHS (LP)	:	480 min. with E-240 video
		cassette
VIDEO/AUDIO (D-VHS)
Format	: MPEG2 standard mode
Track composition
Tape speed	:	16.67 mm/sec (STD mode)
		5.56 mm/sec (LS3 mode)
Head azimuth	: ±30 deg
Drum rotation	:	1800 rpm
Tracking system	: CTL track system
Recording specification
Main data input rate:		14.1 Mbps (STD mode)

4.7Mbps (LS3 mode)

Sub data input rate : 0.146 Mbps (STD mode)

	48.7 Kbps (LS3 mode)
Recording rate	: 19.14 Mbps
Track structure	: 1 Sector
Length of sync block: 112 bytes
Inner ECC	: RS code
Outer ECC	: RS code
Code word shuffling: 6 tracks
Modulation system	: SI-NRZI
VIDEO/AUDIO (S-VHS/VHS)
Format	: S-VHS/VHS PAL standard
Signal system	: PAL-type colour signal and CCIR
	monochrome signal, 625 lines
	50 fields
Recording system	: DA4 (Double Azimuth) head
	helical scan system
Signal-to-noise ratio	: 45 dB
Horizontal resolution	: 250 lines (VHS)
	400 lines (S-VHS)
Frequency range	: 70 Hz to 10,000 Hz
	(Normal audio)

20 Hz to 20,000 Hz (Hi-Fi audio)

CONNECTOR

Input/Output	: 21-pin SCART connectors :
	IN/OUT x 1, IN/DECODER x 1
	RCA connectors:
	VIDEO IN x 1, AUDIO IN x 2,
	AUDIO OUT x 1
	S-Video connectors:
	IN x 2, OUT x 1
	DV connector : IN x 1
	(4-pin, IEEE1394 conformity,
	digital input)
TUNER/TIMER
TV channel storage
capacity	: 99 positions
	(+AUX position)
Tuning system	: Frequency synthesized tuner
Channel coverage	: VHF 47 – 89/104 – 300/
	302 – 470MHz
	UHF 470 – 862MHz

Memory backup time : Approx. 60 min.

ACCESSORIES

Provided accessories : RF cable, S-Video cable,

21-pin SCART cable, DV cable,

Power cord,

Infrared remote control unit, "R6" battery x 2

Specifications shown are for SP mode unless otherwise specified.

E.& O.E. Design and specifications subject to change without notice.

Image 82

JVC HM-DR10000EU specifications Recording specification, PAL-type colour signal and Ccir

Contents

HM-DR10000EU Safety Precautions MTP PAL Late symptom Block noise Still image Symptoms of dirty video headsEarly symptom Do not place the recorder Situate Recorder Check ContentsBasic Connection Mains Connect Recorder to Mains Video ConnectionConnect Recorder to TV Back of Recorder If you are referring to the front display panel Auto Set UpIf you are referring to the on-screen display Language Code Press %Þ to move Highlight bar pointer to Preset DownloadPress %Þ to select CH - and press OK or # Link and press OK Just Clock If both auto channel set and auto clock set have failedLanguage for the on-screen display Just Clock on Language Screen ENABLE/DISABLE ON-SCREEN Display On-Screen Displays Mode Power Save ModeSelect Power Save Return to Normal Screen Access Mode SET Screen Access Main Menu ScreenLink Functions About Ntsc Playback Colour System SetReturn to Normal Screen Press %Þ to move the highlight bar pointer to Point Basic PlaybackLoad a Cassette Start Playback Still Picture/Frame-By-Frame Playback Playback FeaturesPause During Playback Press Pause Override Automatic Tracking Adjust TrackingActivate HIGH-SPEED Search Manually Activate Index Search Index Search Digital TBC/NR S-VHS/VHS Mode Only Digital 3R S-VHS/VHS Mode Only Repeat Playback Soundtrack Selection D-VHS Mode Soundtrack Selection S-VHS/VHS ModeDuring Playback Basic Recording Compatibility Of Cassettes And Recording Mode Recording Mode Select Channel to Watch Recording FeaturesEngage ITR Mode Start Recording Display Remaining Time Reset CounterSET Counter Display Elapsed Recording Time Indication VHS Super VHS And VHS Receiving Stereo And Bilingual Programmes Audio Rec Mode Setting D-VHS Mode OnlyTo Record Stereo And Bilingual Programmes A2 Preparation Select B.E.S.T. ModeS.T. Picture S.T., then press OK or Playback RecordingOr press Record on the recorder Timer Programming VHS or VHS mode VHS mode Press STD/LS3Satellite Tuner Users Start Time Express Timer ProgrammingTime SET Tape Speed SET VPS/PDC ModeTimer Mode Engage RECORDER’S Press Again to check More information. Each Check, Cancel And Replace ProgrammesPress ä or äTIMER Time you press SET, then press OK or # Auto SP→LP Timer S-VHS/VHS Mode OnlyFor Example Then press OK or #to select Auto TIMER, then press Auto TimerHighlight bar pointer to Mode SET, then press OK or #to select either SET Tape Speed Prog REC ModeAutomatic Satellite Programme Recording Before performing the following steps Load a Recorded Cassette Access Title ScreenNavigation Choose a Programme Check Memory Access Main Menu ScreenAccess Video Navigation Screen Turn OFF Navigation Title Editing Access VideoEdit Tape Title Select Category Enter CharacterEnter Character Entering Character Delete Tape Data Select Tape TitleDelete Tape Data Delete Programme Data Delete ProgrammeData To delete, then press Access Sorting Screen Sorting By Tape Number Sorting By Date Sorting By Category Remote A/B Code Switching Remote Control FunctionsSET Remote Control Code SET TV Brand Code TV Multi-brand Remote ControlTV/VCR, TV +/- Volume Operate TV Brand Code Satellite Tuner Multi-Brand Remote ControlSET Satellite Tuner TV Prog +/-,NUMBER keys Preparation For Editing Access Mode SETControl SET Mode Select Picture Edit From Camcorder If the camcorder has a DV OUT connector Recorder DV Sound SettingIf the camcorder has an S-VIDEO output connector Recorder Edit To Or From Another Video Recorder Recorder Player AV1 Select Setting AV2 Select Setting Synchro Editing Synchro Edit connector Lanc Cable not providedRepeat steps 5 7 as necessary Terminal Jlip Joint Level Interface Protocol Connector Access Initial SET ScreenAccess Jlip ID NO. SET Screen SET Jlip ID Number Satellite Tuner Unit Connection To Satellite TunerSimple Connections Back of TV Perfect Connections Connectors ScartDecoder Basic Connections Cable Connect Decoder Connecting Using a DecoderSelect Input Mode SET Tuner Connecting Using a Stereo System Rear View Tuner Set Access Auto CH SETAuto Channel Set Perform Auto Channel SET View Confirmation Screen Select Band Access Main MenuAccess Confirmation Screen Input Channel Change Station Channel Position When Receiving a Scrambled BroadcastDelete a Channel Press %Þ @ #until the item you want to move begins Enter NEW Character TV Station And ID List Fine-Tuning Channels Already Stored Access Manual Channel SET ScreenPerform Tuning Select Channel to FINE-TUNE Enter Receiving Channel Position Number Showview SetupNumber Guide Program Number Set Clock Set Access Initial SET ScreenAccess Clock SET Screen Turn the Recorder on SET Just Clock Default setting is OFF. Set as desired by pressingRecorder is preset to receive clock setting Channel position to the number representing Remote control wont function No power is applied to the recorderPress Play to turn the indicator off Check the cassette Timer Recording Error Code Ä remain lit on the display panel. Is there Problem? Quest Ions and Answers Pull the front panel to access covered buttons/connectors Index Inside View of Front Panel Rear View Display does not show the -2 of -200000. In this If the counter exceeds -20 hours -200000,Case, confirm the counter on the TV screen 80 EN Remote Control LCD Recording specification PAL-type colour signal and Ccir Automatic Satellite Programme Recording Express Timer ProgrammingManual Channel Setting Manual Tracking Change Station Channel Position Ex. Francais is selected for Belgium Ex. Deutschland is selectedInternational Telephone Language Code