Manuals / JVC / TV and Video / DVR

JVC HM-HDS1EU specifications Other Problems, Symptom, Possible Cause, Corrective Action

Models: HM-HDS1EU

1 100

Download 100 pages 24.56 Kb

Page 93

OTHER PROBLEMS

			EN 93
OTHER PROBLEMS

	SYMPTOM	POSSIBLE CAUSE	CORRECTIVE ACTION
1.	Whistling or howling is heard from	● The camcorder’s microphone is too	Position the camcorder so its
	the TV during camcorder	close to the TV.	microphone is away from the TV.
	recording.	● The TV’s volume is too high.	Turn the TV’s volume down.
		● The TV’s volume is too high.	Turn the TV’s volume down.

2.	When scanning channels, some of	● Those channels have been	If you need the skipped channels,
	them are skipped over.	designated to be skipped.	restore them ( pg. 82).

3.	The channel cannot be changed.	● Recording is in progress.	Press 9 to pause the recording,
			change channels, then press 4 to
			resume recording.

4.	Channel settings that were made	● After the manual settings were	Perform manual setting again.
	manually seem to have changed or	made, Auto Channel Set was
	disappeared.	performed.

5.	No channels are stored in the	● The TV aerial cable was not	Turn off the recorder once and
	recorder’s memory.	connected to the recorder when	connect the TV aerial cable to the
		Auto Set Up was performed.	recorder properly, then turn on the
			recorder again. The recorder will try
			Auto Set Up again ( pg. 14).
		● The fully-wired 21-pin SCART cable	Turn off the recorder once and
		was not connected between TV and	connect the fully-wired 21-pin
		the recorder when Preset	SCART cable to the recorder properly,
		Download was performed.	then turn on the recorder again. Then
			perform Preset Download again
			( pg. 16).

6.	The remote control won’t operate	● The remote control brand setting is	Re-set the remote control to the
	the TV or satellite receiver.	incorrect.	correct brand. ( pg. 49, 50)

ATTENTION

This recorder contains microcomputers. External electronic noise or interference could cause malfunctioning. In such cases, switch the recorder off and unplug the mains power cord. Then plug it in again and turn the recorder on. Take out the cassette. After checking the cassette, operate the unit as usual.

Image 93

JVC HM-HDS1EU specifications Other Problems, Symptom, Possible Cause, Corrective Action

Contents

SAFETY FIRST CONTENTSINITIAL SETTINGS TIMER RECORDINGSAFETY FIRST Safety Precautions2 EN WARNING DANGEROUS VOLTAGE INSIDEPage PRECAUTION FOR Hard Disk Drive SAFETY FIRST cont4 EN INDEX FRONT VIEW6 EN REAR VIEWINDEX cont VPS/PDC FRONT DISPLAY PANEL8 EN ON-SCREEN DISPLAY for HDD deckINDEX cont ON-SCREEN DISPLAY for VHS deck REMOTE CONTROL 10 ENINDEX cont Remote Control LCD How To UseINSTALLING YOUR NEW RECORDER A Check the contents12 EN B Situate the recorderA Connect the recorder to TV S-VIDEO ConnectionB Connect the recorder to mains 8To connect to a TV with S-VIDEO/AUDIO IN connectorsINITIAL SETTINGS Auto Set Up14 EN Auto Channel Set/Auto Clock Set/ Auto Guide Program Number SetC Select the language D Perform Auto Set UpOn the front display panel On the on-screen displayA Perform Preset Download Preset DownloadINITIAL SETTINGS cont 16 ENINFORMATION Language for the on-screen displayJust Clock B Access the Tuner Set screen A Access the Main Menu screenC Access the Country Set screen LanguageInstalling Satellite Controller Satellite Receiver Control SettingSAT CONTROL SET A Situate the Satellite ControllerC Access the Initial Set screen Setting satellite receivers brand and channelB Access the Main Menu screen on the recorder D Access the Sat Control Set screenVCR Auto Standby TV Auto Power OnDirect Rec SAT CONTROL SET cont22 EN Basic RecordingB Select the HDD deck C Choose a programmeC Start playback Basic PlaybackD Pause playback E Stop playback24 EN Playback with HDD NavigationRECORDING/PLAYBACK ON HDD DECK cont The Icons and their meaningsScan for Beginnings of Programmes C Access the Index screenD Select the programmes E Start playback26 EN Live Memory PlaybackD Start Live Memory Playback E Stop Live Memory PlaybackHigh-Speed Search Playback FeaturesSlow Motion Still Picture/Frame-By-Frame PlaybackVariable Speed Search 28 ENQuick Rewind a little Quick Skip ForwardInstant Timer Recording ITR Recording Features2 Engage the ITR mode Receiving Stereo and Bilingual ProgrammesA Load a cassette 30 ENB Select the VHS deck D Set the tape speedD Start playback C Find the programme start pointUsable cassettes Basic Playback32 EN Playback with VCR NavigationRECORDING/PLAYBACK ON VHS DECK cont The Icons and their meaningsScan for Beginning of Programme with VCR Navigation C Access the VCR Navigation screenD Search for the programme E Load the cassettePlayback Features 34 ENHigh-Speed Search Slow MotionNext Function Memory Index Search1 Start playback 2 Activate Repeat Playback36 EN 2 Adjust the tracking manuallyManual Tracking 1 Override automatic trackingRecord One Programme While Watching AnotherRecording Resume Function Accidental erasure prevention1 Engage the Record-Pause mode 2 Reset the counter38 EN Tape Remaining TimeSuper VHS ET S-VHS ET Recording on VHS cassettes with S-VHS quality Engage the S-VHS ET modeReceiving Stereo and Bilingual Programmes 40 ENRECORDING/PLAYBACK ON VHS DECK contOn-screen Display ReceivedPlayback B.E.S.T. Picture SystemRecording DURING B.E.S.T B.E.S.T. COMPLETEC Access the SHOWVIEW display SHOWVIEW Timer ProgrammingTIMER RECORDING 42 ENK Engage the recorder’s timer mode H Set the VPS/PDC modeG Set the recording speed I Set the categoryC Access the programme screen Express Timer ProgrammingTIMER RECORDING cont 44 ENL Engage the recorder’s timer mode I Set the VPS/PDC modeVPS/PDC Recording J Set the categoryCheck, cancel and change programmes To cancel or change a programmeC Access the Programme screen D Cancel or change a programmeRecording mode A Select the L-2 SELECT modeProgramme Recording Automatic SatelliteB Change the remote control code Remote A/B/C/D Code SwitchingC Set the remote control code REMOTE CONTROL FUNCTIONSControl Your TV Using Additional Buttons TV Multi-Brand Remote ControlA Set the TV brand code B Operate the TVREMOTE CONTROL FUNCTIONS cont Satellite Receiver Multi-Brand Remote Control50 EN A Set the satellite receiver brand codeEDITING About Hybrid NavigationThe display for modification or deletion The display for editingE Access the modify screen C Access the Navigation screenModify Information 52 ENModify Programme Title A Access the modify screenB Enter new title C Register new titleModify Category 54 ENB Select new category C Register new categoryDelete Information B Access the delete screenA Select the programme C Confirm the deletionB Access the Easy Dubbing screen A Access the HDD Navigation screenDubbing 56 ENF Load a cassette E Select the VHS deckH Locate the start point I Select the HDD deck58 EN Normal Dubbingfrom HDD to VHS B Prepare the HDD deck for dubbingB Prepare the VHS deck for dubbing from VHS to HDDD Prepare the HDD deck for dubbing Normal DubbingD Access the edit screen C Access the HDD Navigation screenF Access the R.A.Edit screen Random Assemble EditingL Access the Start Editing screen J Access the Start Editing screenI Select other edit-in and edit-out points K Prepare the VHS deck for dubbing62 EN Edit From A CamcorderA Make connections EDITING contB Select the recording deck C Set the recorder’s input modeD Set the edit mode. VHS deck only E Start the camcorderB Access the Input/Output Set screen L-1 OUTPUT and L-1 INPUT SettingC Select the output or input mode for the AV1 L-1 IN/OUT connector Output/Input SetF-1 INPUT Setting L-2 SELECT SettingDECODER connector A Select the input mode for the VIDEO/S VIDEO connectorD Set the edit mode C Set the input mode of recording deckAnother Video Recorder 66 ENRecorder PlayerRecorder Player68 EN Audio DubbingEDITING cont Pre-recorded tapeD Locate the start point E Engage the Audio Dubbing modeF Start dubbing G End Audio DubbingSimple Connections Connecting To A Satellite Receiver70 ENSYSTEM CONNECTIONS Back of TVBack of TV Perfect ConnectionsSatellite receiver DecoderA Select the input mode Connecting/Using A Decoder72 EN B Connect the decoderMake connections Connecting/Using A Stereo SystemCAUTIONS AUDIO OUTB Access the HDD Set Up screen Mode SetC Select the mode D Select the mode settingVCR SET UP HDD SET UP8 LIVE MEMORY 8 AUDIO RECSUBSIDIARY SETTINGS cont VCR SET UP 1 cont8 AUTO SPLP TIMER 76 EN8 PICTURE CONTROL 8 B.E.S.T8 DIGITAL 3R 8 DIGITAL TBC/NR8 AUTO TIMER VCR SET UP 2 cont78 EN FUNCTIONB Access the Initial Set screen SHOWVIEW System SetupC Access the Guide Program Set screen Guide Program Number SetC Access the Tuner Set screen B Access the Main Menu screenD Access the Auto Channel Set screen Tuner SetH View the Confirmation screen G Perform Auto Channel SetI Return to the normal screen You can set up the recorder’s tuner also by PresetC Access the Confirmation screen 82 ENSUBSIDIARY SETTINGS contManual Channel Set D Select the channel positionF Input the channel Delete A ChannelG Enter new channel information H Close the Confirmation screenChange Station Channel Position 84 ENB Select the new position SUBSIDIARY SETTINGS contB Access the Manual Channel Set screen D Switch the stationsSet Stations A Set Stations BFine-Tuning Channels Already Stored When Receiving A Scrambled BroadcastC Perform tuning A Select the decoder modeTV Station And ID List STATION NAMESTATION NAME Clock Set D Access the Clock Set screen88 EN B Access the Main Menu screenF Set Just Clock E Set the date and timeG Set the source channel position for clock data H Start the clock operationTROUBLESHOOTING POWERSYMPTOM 90 ENSYMPTOM RECORDINGPOSSIBLE CAUSE CORRECTIVE ACTIONTROUBLESHOOTING cont TIMER RECORDING92 EN SYMPTOMSYMPTOM OTHER PROBLEMSPOSSIBLE CAUSE CORRECTIVE ACTIONON-SCREEN MESSAGES 94 ENMESSAGE DESCRIPTIONTo set the timer programme using the SHOWVIEW system You can programme this recorder to timer-record as manyThe timer programme you set is overlapping with another The recorder is not in the timer-standby mode. The timerON-SCREEN MESSAGES cont 96 ENTROUBLESHOOTING cont MESSAGEQUESTIONS AND ANSWERS TIMER RECORDINGPLAYBACK RECORDING98 EN SPECIFICATIONSLISTE OF TERMS Auto Set Up - referring to the front display panel FOR MORE INFORMATION SEE INSTRUCTIONS ON PAGEInternational Telephone Country Code