Video Channel Set, Access Video Channel SET Mode | JVC LPT0320-001B

64SUBSIDIARYSETTINGS

Video Channel Set

Video Channel (RF Output Channel) is the channel on which your TV receives picture and sound signals from the video recorder through the RF cable.

8

13

2

IMPORTANT

Perform the following steps only if —

—Video Channel Set has not been done correctly by the Auto Set Up function (☞ pg. 8).

—interference appears in the TV picture after you have moved to a different area or a new station has started broadcasting in your area.

—you change the connection between your recorder and TV from RF connection to AV or S-VIDEO connection, or vice versa.

●If you have connected the video recorder to your TV via both the provided RF cable and a 21-pin SCART cable (AV connection), or via the provided RF cable, an S-Video cable and an audio cable (S-VIDEO connection), you do not need the video channel so you have to set the video channel to off. — Go to "With AV or S-VIDEO Connection" below.

●If you have connected the video recorder to your TV via the provided RF cable only (RF connection), you have to set the correct video channel — Go to "With RF Connection" on page 65.

1

2

1

2

– –:– –

1 2 3

4

5

6

7 8 9

0

3

4

4

3

OK

PR

With AV or S-VIDEO

Connection

Before performing the following procedure, make sure that:

■the mains power cord is plugged into the mains outlet.

■the video recorder is turned off and there is no cassette inserted in the recorder.

■batteries have been installed in the remote control.

ACCESS VIDEO CHANNEL SET MODE

		Press and hold down STOP on the recorder until the
	1 display panel shows the following.
	2	SET VIDEO CHANNEL
	2	Press PR – until the display panel shows "–OUT– –".
		Press PR – until the display panel shows "–OUT– –".

●Now the video channel is set to off.

EXIT VIDEO CHANNEL SET MODE

3 Press OK.

To view picture signals from the video recorder, set your TV to its AV mode. Refer to the instructions supplied with your TV set for how to do this.

Image 64

JVC LPT0320-001B Video Channel Set, Access Video Channel SET Mode, SET Video Channel, Exit Video Channel SET Mode

Contents

HR-S9700EK Safety Precautions Connection to the mains supply in the United Kingdom Moisture Condensation Do not place the recorder Some Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Back of TV Connect Video Recorder to TVBack of Recorder Mains outlet Mains Power Cord Video Connection Before performing the following procedure, make sure that With the AV or S-VIDEO connectionTion pg and the TV is turned on, Go to item Remote control while downloading is 10 or If -- appears on the display panel, referLink screen will appear. Then the Guide Program number set If auto channel set has succeeded but auto clock set has not If both auto channel set and auto clock set have failed Access Main Menu Screen Access Mode SET ScreenLink Functions Turn on the Recorder Satellite Receiver Control Setting Select Satellite RECEIVER’S Channel for Testing Enter Satellite RECEIVER’S BrandCheck Result of Test Satellite Tuner Brand Code Playback Load a CassetteFind Programme Start Point Start Playback Slow Motion Still Picture/Frame-By-Frame PlaybackHigh-Speed Turbo Search Variable-Speed Search Recording Select Preset to Watch Reset CounterEngage ITR Mode SET Counter Display Video Plus+ Timer Programming Access Video PLUS+ ScreenAccess Video PLUS+ Program Screen Enter Pluscode Number Timer Warning PDC Recording Express Timer Programming Enter ProgrammeStart Time Time SET PDC Mode Timer ModeSET Tape Speed Return to Normal Check, Cancel And Replace Programmes When programmes overlap each other Cancel or Change Programme SettingConfirm Overlapping Programmes Modify Navigation Check Memory Return to Normal ScreenTurn OFF Navigation Turn Off Navigation Access Find Blank Space Screen Title EditingSelect Tape Number Load a Cassette Access Video Navigation Screen Enter CharacterEdit Tape Title Select Tape Number Select Category Select ProgrammeEdit Programme Title Category Delete Programme DataDelete Tape Data Delete Programme Data Access Find Title Screen Access Tape NO. ScreenAccess Video Finding Title Access Date Screen Select Programme Access Category ScreenSelect Programme Load a Cassette Sorting By Date Playback Picture Adjustment Adjust TrackingOverride Automatic Tracking Manually SET Mode ModeDigital 3R Video Stabilizer Access REC Level Adjust AudioSelecting Sound You Want Control Screen Receiving Nicam Stereo And Bilingual Programmes Soundtrack SelectionDuring Playback Type of Broadcast On-screen Display Being Received Looking For Scene You Want Activate Index SearchSkip Over Unwanted Sections Recording According To Tape Type Select S-VHS ModeSuper VHS S-VHS VHS ET and VHS Playback/ Recording According To Tape Charac- teristics Select B.E.S.T. ModeS.T. Picture System Start Playback RecordingPlayback During B.E.S.T Audio signal during TimeScan TimeScanSearch Variable-Speed Search/ Reverse Play TimeScan TimeScan AudioSpeed SP Speed LP Speed EP Audio output Forward Search Play Slow-Motion Still Connector TV Aerial cable Audio in connector Automatic Satellite Programme RecordingSatellite Receiver Unit Aerial Access Main Menu Screen Select L-2 Select ModeREC Mode Screen Remote Control Functions Remove Power SupplySET Remote Control Code RE-SUPPLY Power Control Your TV Using Additional Buttons TV Multi-Brand Remote ControlSET TV Brand Code Operate TV Satellite Receiver Multi- Brand Remote Control SET Satellite ReceiverBrand Code Operate Satellite Receiver Access Main Menu Access Mode SETControl SET Mode Minimizing Picture Degradation While Editing Edit From Camcorder Synchro Editing Synchro Edit connector Lanc Cable not providedRepeat steps 4 6 as necessary Input Mode SET Edit ModeEdit To Or From Another Video Recorder SET Recording DECK’S TV Receiver Player Your recorder Recorder Recorder Player OUTPUT/INPUT Setting SELECT/INPUT Setting SET Input Mode Locate Start PointEngage Audio Dubbing Start Dubbing Insert Editing Reset the CounterLocate END Point Engage Insert Editing Start EditingEND Insert Editing DUB Random As- semble Editing Prepare for EditingLoad Source Cassette Press R.A.EDIT Locate EDIT-IN Point Locate EDIT-OUT PointStart R.A.EDIT END R.A.EDIT Terminal JLIPJoint Level Interface Protocol Connector Access Initial SET ScreenAccess Jlip ID NO. SET Screen Information On J Terminal ENABLE/DISABLE Other FunctionsON-SCREEN Display On-Screen Display Power Save Mode Select Power Save ModePress %Þ to move the highlight bar pointer to Access Mode SET Screen Auto TimerAuto SP→LP Timer Next Function Memory Stop Playback Engage RECORD-PAUSE ModeResume Recording Connection To Stereo System Speaker Television Access Video Channel SET Mode Exit Video Channel SET ModeVideo Channel Set SET Video Channel Inserted in the recorder With RF ConnectionConnected TV is turned on Tuner Set Perform Auto Channel SETAuto Channel Set Pointer to Auto CH View Confirmation Screen Storing Channels Manually Input ChannelEnter NEW Channel Information Close Confirmation Screen When Receiving a Scrambled Broadcast Change Station Preset PositionFine-Tuning Channels Already Stored Delete a Channel Enter NEW Character TV Station And ID List Station Name TV Station Channel Number Guide Clock Set Number Video Plus+ System SetupGuide Program Number Set Ä remain lit on the display panel. Is there Problem? Questions And AnswersWhat happens if the tape runs out during recording? Troubleshooting Timer Recording Won’t stop blinking Record Safety tab removed Index Front View Inside View of Front Panel 3 4 5 6 @ # $ Rear View Display Panel VCR Remote Control TV Muting Button mutes sound Remote Control LCD Fast Forward FF Button same as button on Maximum recording time Mm x 106 mm x 352 mmDA4 Double Azimuth helical