77

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4.

Camcorder recording is not

The camcorder has not been

Confirm that the camcorder is

 

 

 

possible.

properly connected.

properly connected.

 

 

 

 

 

 

 

The input mode is not correct.

Set the input mode to “L-1”,“L-2”,

 

 

 

 

 

 

 

 

 

 

“F-1” or “S-1”.

 

 

 

 

 

 

 

 

 

 

 

 

TIMER RECORDING

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SYMPTOM

 

POSSIBLE CAUSE

 

CORRECTIVE ACTION

 

 

1.

Timer recording won’t work.

The clock and/or the timer have

Re-perform the clock and/or timer

 

 

 

 

 

 

 

been set incorrectly.

settings.

 

 

 

 

 

 

 

The timer is not engaged.

Press ä and confirm that “ä“ is

 

 

 

 

 

 

 

 

 

 

displayed on the display panel.

 

 

 

 

 

 

 

 

2.

Timer programming is not possible.

Timer recording is in progress.

Timer programming can’t be

 

 

 

 

 

 

 

 

 

 

performed while a timer recording is

 

 

 

 

 

 

 

 

 

 

in progress. Wait until it finishes.

 

 

 

 

 

 

 

 

3.

“ä“ and “]“ on the display

The timer is engaged but there’s no

Load a cassette with the Record

 

 

 

panel won’t stop blinking.

cassette loaded.

Safety tab intact, or cover the hole

 

 

 

 

 

 

 

 

 

 

using adhesive tape.

 

 

 

 

 

 

 

 

4.

The power shuts off and “ä“ and

The loaded cassette has had its

Remove the cassette and cover the hole

 

 

 

“]“ won’t stop blinking.

Record Safety tab removed.

with adhesive tape, or insert a cassette

 

 

 

 

 

 

 

The end of the tape was reached

with the Record Safety tab intact.

 

 

 

 

 

 

 

during timer recording.

The programme may not have been

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

recorded in its entirety. Next time

 

 

 

 

 

 

 

 

 

 

make sure you have enough time on

 

 

 

 

 

 

 

 

 

 

the tape to record the entire

 

 

 

 

 

 

 

 

 

 

programme.

 

 

 

 

 

 

 

 

5.

“ä“ blinks for 10 seconds and the

ä has been pressed when there are

Check the programmed data and re-

 

 

 

Timer mode is disengaged.

no programs in memory, or the timer

programme as necessary, then press

 

 

 

 

 

 

 

record information has been

ä again.

 

 

 

 

 

 

 

programmed incorrectly.

 

 

 

 

 

 

 

 

 

 

 

 

6.

The VIDEO Plus+ system does not

The recorder’s preset positions have

Refer to "Guide Program Number Set"

 

 

 

timer-record properly.

been set incorrectly.

and re-perform the procedure (pg. 74).

 

 

 

 

 

 

 

 

 

 

 

 

OTHER PROBLEMS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SYMPTOM

 

POSSIBLE CAUSE

 

CORRECTIVE ACTION

 

 

1.

Whistling or howling is heard from

The camcorder’s microphone is too

Position the camcorder so its

 

 

 

the TV during camcorder record-

close to the TV.

microphone is away from the TV.

 

 

 

ing.

The TV’s volume is too high.

Turn the TV’s volume down.

 

 

 

 

 

 

 

 

2.

When scanning channels, some of

Those channels have been desig-

If you need the skipped channels,

 

 

 

them are skipped over.

nated to be skipped.

restore them (pg. 68).

 

 

 

 

 

 

 

 

3.

The preset cannot be changed.

Recording is in progress.

Press PAUSE to pause the recording,

 

 

 

 

 

 

 

 

 

 

change presets, then press PLAY to

 

 

 

 

 

 

 

 

 

 

resume recording.

 

 

 

 

 

 

 

 

4.

Channel settings that were made

After the manual settings were

Perform manual setting again.

 

 

 

manually seem to have changed or

made, Auto Channel Set was

 

 

 

 

 

 

 

disappeared.

performed.

 

 

 

 

 

 

 

 

 

 

 

 

5.

No channels are stored in the

The TV aerial cable was not

Turn off the recorder once and connect

 

 

 

recorder's memory.

connected to the recorder when

the TV aerial cable to the recorder

 

 

 

 

 

 

 

Auto Set Up was performed.

properly, then turn on the recorder

 

 

 

 

 

 

 

 

 

 

again. The recorder will try Auto Set

 

 

 

 

 

 

 

 

 

 

Up again (pg. 8).

 

 

 

 

 

 

 

The fully-wired 21-pin SCART cable

Turn off the recorder once and connect

 

 

 

 

 

 

 

was not connected between TV and

the fully-wired 21-pin SCART cable to

 

 

 

 

 

 

 

the recorder when Preset Download

the recorder properly, then turn on the

 

 

 

 

 

 

 

was performed.

recorder again. Then perform Preset

 

 

 

 

 

 

 

 

 

 

Download again (pg. 9).

 

 

 

 

 

 

 

 

6.

The remote control won’t operate

The remote control brand setting is

Re-set the remote control to the

 

 

 

the TV or satellite receiver.

incorrect.

correct brand (pg. 45, 46).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Page 77
Image 77
JVC HR-S9700EK, LPT0320-001B setup guide Timer Recording, Won’t stop blinking Record Safety tab removed