JVC Model SR-TS1U manual Connections

6ENINSTALLING YOURNEWVCR

Connections		Basic Connections
		1	CHECK CONTENTS
			Make sure the package contains all of the accessories
Antenna or Cable			listed in “SPECIFICATIONS” ( pg. 68).
	ANTENNA IN
	(Antenna or Cable input)		SITUATE VCR
	Coaxial Cable	2
			Place the VCR on a stable, horizontal surface.
	Flat Feeder		CONNECT VCR TO TV
AC Outlet	Transformer
	Matching
AC Power Cord	(Not supplied)	3	The connection method you use depends on the type of
			TV you have.

					RF Connection
					To Connect To A TV With NO AV Input Terminals . . .
	CABLE	IN OUT			a– Disconnect the TV antenna from the TV.
	BOX		ANTENNA IN		b– Connect the TV antenna cable to the ANTENNA
		R
	S VIDEO	AUDIO	TV OUT		IN jack on the rear of the VCR.
		(MONO)
	IN OUT	L	VHF/UHF
		VIDEO	CH3		c– Connect the supplied RF cable between the TV
		REMOTE	CH4
					OUT jack on the rear of the VCR and the TV’s
Back of VCR					antenna terminal. Set TV on CH3 or CH4
	AUDIO				corresponding to the CH3 – CH4 switch setting on
		VIDEO			the back of the VCR.
	OUT		TV OUT		AV Connection
		OUT
					To Connect To A TV With AV Input Terminals . . .
	Audio/Video				a– Connect the antenna, VCR and TV as shown in
			RF Cable		the illustration.
	Cable (supplied)
			(supplied)		b– Connect an Audio/Video Cable between the AUDIO
					OUT and VIDEO OUT jacks on the rear of the VCR
					and the AV IN jacks on the TV. Set your TV in video
					input mode or A/V input mode. Refer to the TV
					Instruction Manual.
					S-VIDEO Connection
		75 ohm terminal			If you have a TV with S-VIDEO input terminals, see
	TV				"S-VIDEO Connection" on page 7.
		Back of VCR			CONNECT VCR TO
			CH3	4	POWER SOURCE
		TE	CH4		Connect the power plug to an AC outlet.
					The clock and tuner channels will automatically be
					set when the antenna is connected and when the AC
					is first connected to the VCR (		pg. 8).
NOTES:					(If "Auto" or "CH" is displayed on the front display
					panel before the VCR is powered on, the clock and
The VCR channel is the channel on the TV which will display					tuner channels are being set automatically. Wait for
					the time to be displayed on the front display panel
the audio and video signals from the VCR. The VCR's CH3-
					before powering on the VCR.)
CH4 switch, on the back of the VCR, sets the VCR channel to
CH3 or CH4.					FINAL PREPARATION FOR
The CH3–CH4 switch is preset to the CH3 position.
Set to CH4 if CH3 is used for broadcasting in your area and					USE
set the channel on the TV to correspond to the VCR's CH3–
CH4 switch setting.					Power on the VCR and if you have connected the VCR
If you have connected the VCR to the TV using the RF connector,					to the TV using the RF connector, select the VCR
you may need to press CH UP and then CH DOWN on the TV				5 channel (3 or 4) by setting the switch on the rear of the
when switching between the TV and VCR input modes, to
maintain good picture quality.					VCR as shown in the illustration.
					You can now perform simple playback (			pg. 22) or
Even if you are using AV cables to connect your VCR to your					simple recording (	pg. 23).
TV, you must also connect it using the RF cable. This will
ensure that you can record one show while watching another
(	pg. 38).
For full identification of the VCR's rear panel, refer to the
Index (REAR VIEW		pg. 66).