JVC RX-9000VBK manual Basic Settings, Setting the Front Speakers Either for Main Room or Sub-room

SOURCE SELECTOR

Basic Settings

Some of the following settings are required after connecting and positioning your speakers, while others will make operations easier.

The following operations are only possible while the receiver is ready for the main room operations.

IMPORTANT:

When using the buttons and controls on the front panel:

Check the following lamps’ illumination.

For the main room operations:

•The MAIN ROOM ON/OFF lamp is lit.

•The SUB ROOM CONTROL lamp is not lit.

When using the remote control:

Check to see if the multi-room operation selector and the remote control mode selector are set to the correct positions:

Multi-room operation selector:

Setting the Front Speakers Either for the

Main Room or Sub-room

You can use the front speakers connected to the FRONT 2/SUB ROOM SPEAKERS terminals either as the 2nd front speakers in the main room or as the front speakers in the sub-room.

Before you start, remember...

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

To operate this receiver for the main room, set

it to “MAIN ROOM.”

Remote control mode selector:	MAIN		SUB
	ROOM	ROOM
To operate this receiver, set it to “AUDIO/TV/
VCR.”	AUDIO/
	TV/VCR

On the front panel ONLY:

1. Press SETTING repeatedly until “SPEAKER 2” appears on the display.

SETTING

CATV/DBS

Changing the Source Name

When you have connected an MD recorder to the TAPE/MD jacks or the DBS tuner to the TV SOUND/DBS jacks on the rear panel, change the source name which will be shown on the display when you select the MD recorder or DBS tuner as the source.

On the front panel ONLY:

1. When changing the source name from “TAPE” to “MD”:

•Turn SOURCE SELECTOR until “TAPE” appears.

When changing the source name from “TV SOUND” to “DBS”:

•Turn SOURCE SELECTOR until “TV SOUND” appears.

The display changes to show the current setting.

MULTI JOG

2.Turn MULTI JOG to specify the way you want to use the speakers connected to the FRONT 2/SUB ROOM terminals.

• As you turn it, the display changes to show the following:

MAIN SUB

MAIN: Select this to use as the 2nd front speakers in the main room.

SUB: Select this to use as the front speakers in the sub- room.

Setting the Subwoofer Information

Register whether or not you have connected a subwoofer.

Before you start, remember....

2. Press and hold SOURCE NAME (BASS BOOST) until “ASSGN.

BASS BOOST

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

On the front panel:

SOURCENAME

MD” or “ASSGN. DBS” appears on the display.

To change the source name to “TAPE” or “TV SOUND,” repeat

the same procedure above — in step 1, select “MD” or “DBS” then press and hold SOURCE NAME (BASS BOOST).

Notes:

•You can only assign the correct source name to “TAPE/MD” and “TV SOUND/DBS,” but not to “CDR/VCR 2.”

•Without changing the source name, you can still use the connected components. However, there may be some inconvenience.

–“TAPE” or “TV SOUND” will appear on the display when you select the MD recorder or DBS tuner.

–You cannot use the digital input (see page 26) for the MD recorder.

–You cannot use the COMPU LINK remote control system (see page 47) to operate the MD recorder.

SETTING

1.Press SETTING repeatedly until “SUBWOOFER” appears on the

display.

The display changes to show the current setting.

MULTI JOG

2.Turn MULTI JOG to register whether you have connected a subwoofer or not.

•As you turn it, the subwoofer setting alternates between “YES” and “NO.”

YES: Select this when a subwoofer is used. SUBWFR lights up on the display (see page 16).

NO: Select this when no subwoofer is used.

23