JVC RX-9000VBK manual VCR 1 VCR connected to VCR 1 jacks, DVD player, Multi only for the main room

IMPORTANT:

To operate JVC’s video components using this remote control:

•You need to connect JVC video components through the AV COMPU LINK terminals (see page 54) in addition to the connections using cables with RCA pin plugs (see pages 7 and 8).

•Some JVC VCRs can accept two types of the control signals — remote codes “A” and “B.” Before using this remote control, make sure that the remote control code of the VCR connected to the VCR 1 jacks is set to code “A.”

–When another JVC VCR is connected to the CDR/VCR 2 jacks, set its remote control code to code “B.” (This remote control cannot emit the control signals of code “B.”)

•To operate the video components only using this remote control, aim the remote control at the remote sensors on the target video component(s) directly. (For the TV having AV COMPU LINK terminal “RECEIVER/AMP,” aim the remote control directly at the remote sensor on the receiver.)

•To operate the video component(s) using the RF signals emitted from this remote control, the IR signal transmitter and the RF rod antenna must be connected to this receiver.

–Place the IR signal transmitter so that it is aimed at the remote sensor on the target video component(s).

–The RF signal-reachable distance may differ depending on the operating conditions and circumstances.

–The IR signal transmitter can send signals at a distance of 10 feet (3 m).

VCR 1 (VCR connected to the

VCR 1 jacks)

You can always perform the following operations (with the remote control mode selector set to “AUDIO/TV/VCR”):

VCR 1 POWER: Turns on or off the VCR 1.

After pressing VCR 1 or VCR 1 CONTROL (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the following operations on the VCR 1:

1 – 9, 0: Selects the TV channels on VCR 1.

PLAY: Starts playing.

REW: Rewinds a tape.

FF: Fast winds a tape.

STOP: Stops operations.

PAUSE: Pauses playing. To release it, press PLAY.

ƒREC: Press this button with the PLAY button to start recording. (Only for the main room operations) Press this button with the PAUSE button to enter

recording pause.

CHANNEL +/–: Changes the TV channels on the VCR.

Note:

You can use either VCR 1 button or the VCR 1 CONTROL button to activate the buttons listed above. If you press VCR 1, the playing source also changes. On the other hand, if you press VCR 1 CONTROL, the playing source does not change.

		MAIN		SUB
		ROOM	ROOM			STANDBY	ON
		MAIN ROOM		SUB ROOM TV/CATV/DBS			VCR 1
		ON/OFF		ON/OFF		POWER	POWER
MAIN	SUB	DVD		DVD MUILTI		CD	TAPE/MD
ROOM	ROOM
		TV/DBS		VIDEO		PHONO	FM/AM
Check to see if the		VCR 1		CDR/VCR 2 ANALOG/DIGITAL			SLEEP
multi-room		SURROUND		CNTR TONE		CENTER
operation selector		ON/OFF		1		2	3
						MENU
is set to the		SURROUND		REAR TONE		REAR-L
		MODE		4		5	6
correct position.						ENTER
		CD-DISC		SEA MODE		REAR-R
To operate the				7/P		8	9
		SOUND		TEST		SUBWOOFER
receiver for the
				10		0	+10	AUDIO/
main room, set it				RETURN		FM MODE	100+
								TV/VCR
to “MAIN ROOM.”							AUDIO/
							TV/VCR
To operate the								CATV/DBS
		MENU
							CATV/DBS
receiver for the					SET
sub-room, set it		EXIT					TEXT
							DISPLAY
								Check to see if the
to “SUB ROOM.”
								remote control
		TV VOL		CHANNEL		VOLUME		mode selector is set
								to the correct
								position.
		TV/VIDEO		VCR 1		TAPE/MD	MUTING	To operate the
				CONTROL
		/REW			PLAY		FF/	audio system, TVs,
		DOWN		TUNING			UP	VCRs, and DVD
		REC			STOP		PAUSE
								players, set it to
								“AUDIO/TV/VCR.”
		RM-SRX9000J			REMOTE CONTROL

DVD player

After pressing DVD (or DVD MULTI: only for the main room operations) (with the remote control mode selector set to “AUDIO/ TV/VCR”), you can perform the following operations on a DVD player:

PLAY:		Starts playing.
4:		Returns to the beginning of the current (or previous) track.
¢:		Skips to the beginning of the next track.
STOP:		Stops playing.
PAUSE: Stops playing temporarily. To release it, press PLAY.
	After pressing DVD (or DVD				CENTER
				2	3
	MULTI: only for the main room
					MENU
	operations), these buttons can be
			REAR TONE		REAR-L
	used for the DVD menu operations.		4	5	6
					ENTER
	Note:				REAR-R
				8

For detailed menu operations, refer to the instructions supplied with the discs or the DVD player.

TV

You can always perform the following operations only for the main room operations (with the remote control mode selector set to “AUDIO/TV/VCR”):

TV/CATV/DBS POWER: Turns on or off the TV.

TV VOL +/–: Adjusts the volume.

TV/VIDEO: Sets the input mode (either TV or VIDEO).

After pressing TV/DBS (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the following operations on a TV:

CHANNEL +/–: Changes the channels.

1 – 9, 0, 100+: Selects the channels.

RETURN: Alternates between the previously selected channel and the current channel.

59