JVC RX-9000VBK Adjusting the Sub-roomVolume, Muting the Sub-roomSound, On the front panel, again

Adjusting the Sub-room Volume

Muting the Sub-room Sound

On the front panel:

To increase the volume, turn MASTER

MASTER VOLUME

From the remote control ONLY:

Press MUTING to mute the sound through MUTING

–

VOLUME clockwise.

+

the front speaker in the sub-room.

To decrease the volume, turn it counterclockwise.

•When you turn MASTER VOLUME rapidly, the volume level also changes rapidly.

•When you turn MASTER VOLUME slowly, the volume level also changes slowly.

The volume level indicator goes off.

To restore the sound, press MUTING again so that the volume level indicator appears on the display.

•Turning MASTER VOLUME on the front panel or pressing VOLUME +/– on the remote control also restores the sound.

From the remote control:

To increase the volume, press VOLUME +. To decrease the volume, press VOLUME –.

CAUTIONS:

VOLUME

Operating the Playback Source for the

Sub-room

•Always set the volume to the minimum before starting any source. If the volume is set at its high level, the sudden blast of sound energy can permanently damage your hearing and/or ruin your speakers.

•Be careful not to turn up the volume so high when controlling the receiver without listening to the playback sound. For example, when adjusting the volume level in the sub-room from the main room.

Note:

The volume level can be adjusted within the range of “0” (minimum) to “90” (maximum).

Activating the Sub-room Front Speakers

This section is not for the persons who connect the sub-room front speakers to the SUB ROOM PRE OUT jacks using another amplifier (see page 12).

Before you start, remember...

•When shipped from the factory, both pairs of the front speakers have been set to be used in the main room. To use the front speakers connected to the FRONT 2/SUB ROOM SPEAKERS terminals for the sub-room, see “Setting the Front Speakers Either for the Main Room or Sub-room” on page 23.

On the front panel ONLY:

Press SUB ROOM (SPEAKERS 2) to activate		SPEAKERS
the front speakers in the sub-room.		1	2
The lamp on the button lights green.	MAIN ROOM		SUB ROOM
• Each time you press the button, the lamp on
		MULTI ROOM
the button turns on and off.
To deactivate the front speakers in the sub-		SPEAKERS
		1	2
room, press SUB ROOM (SPEAKERS 2)
again.	MAIN ROOM		SUB ROOM
		MULTI ROOM

Note:

If the center speaker or rear speakers are used for the DSP mode (see page 32) for the main room operations, the SUB ROOM (SPEAKERS 2) button does not work.

•When you select “FM” or “AM” as the sub-room source, you can do the following:

–Tune into any station frequency manually (see page 29).

–Select a preset station (see page 30).

–Select FM reception mode (see page 30).

•When you select the other sources as the sub-room source, you can operate them by using the remote control supplied with this receiver. (“TV SOUND,” “DVD MULTI” and the digital input cannot be selected as the sub-room source.)

–If they are one of the JVC products equipped with the COMPU LINK remote control system or the AV COMPU LINK remote control system, see pages 57 to 59.

–If they are one of the JVC products, but not equipped with the above remote control systems, or if they are the products of the other manufacturers, see pages 60 to 62.

CAUTION:

Be careful not to turn up the volume so high when controlling the receiver without listening to the playback sound. For example, when adjusting the volume level in the sub-room from the main room.

Notes:

•Any sound adjustments such as the SEA or DSP modes cannot be applied to the sub-room source. You can only adjust the volume level.

•The One Touch Operation function (see page 28) cannot be used for the sub-room sources.

22