3)Repeat 1) and 2) to adjust the other speaker output levels.
| BALANCE/SURROUND | ||
3. Adjust the center tone. |
| ADJUST | |
|
|
|
1)Press BALANCE/SURROUND ADJUST repeatedly until “CENTER TONE” appears on the display.
The display changes to show the current
MULTI JOG
setting.
2)Turn MULTI JOG to select the center tone level you want.
•As you turn it, the display changes to show the following:
CENTER SHARP1 CENTER SHARP2 CENTER FLAT
(Canceled)
CENTER SOFT 1 CENTER SOFT 2
To make the dialogue clearer, select “CENTER SHARP1” (a little) or “CENTER SHARP2” (much).
To make the dialogue softer, select “CENTER SOFT 1” (a little) or “CENTER SOFT 2” (much).
When “CENTER FLAT” is selected, no adjustment is applied.
6. Adjust the room size (sense of | BALANCE/SURROUND | ||
spaciousness). |
| ADJUST | |
|
|
| |
1) Press BALANCE/SURROUND |
|
|
|
ADJUST repeatedly until “ROOM |
|
|
|
SIZE” appears on the display. |
|
|
|
The display changes to show the current |
| MULTI JOG | |
setting. |
|
|
|
2)Turn MULTI JOG to select the room size.
•As you turn it, the room size changes as follows:
ROOM SIZE 1ROOM SIZE 2ROOM SIZE 3
ROOM SIZE 5 | ROOM SIZE 4 |
As the number increases, the interval between reflections increases so that you will feel as if you were in a larger room. (Normally set it to “ROOM SIZE 3.”)
7. Adjust the liveness. | BALANCE/SURROUND | ||
| ADJUST | ||
|
|
|
1)Press BALANCE/SURROUND ADJUST repeatedly until “LIVENESS” appears on the display. The display changes to show the current
setting. | MULTI JOG |
4.Adjust the rear tone.
1)Press BALANCE/SURROUND ADJUST repeatedly until “REAR TONE” appears on the display.
The display changes to show the current setting.
2)Turn MULTI JOG to select the rear tone level you want.
BALANCE/SURROUND
ADJUST
MULTI JOG
2)Turn MULTI JOG to select the liveness effect.
•As you turn it, the liveness level changes as follows:
LIVENESS 1 LIVENESS 2 LIVENESS 3
LIVENESS 5 | LIVENESS 4 |
As the number increases, the attenuation level of reflections over time decreases so that acoustics change from “Dead” to “Live.”
•As you turn it, the display changes to show the following:
REAR SHARP1 REAR SHARP2 REAR FLAT
(Canceled)
REAR SOFT 1 REAR SOFT 2
To make the rear sounds clearer, select “REAR SHARP1” (a
little) or “REAR SHARP2” (much).
To make the rear sounds softer, select “REAR SOFT 1” (a little) or “REAR SOFT 2” (much).
When “REAR FLAT” is selected, no adjustment is applied.
5. Adjust the overall level of the effects.
(Normally set it to “LIVENESS 3.”)
From the remote control:
When using the remote control, you cannot adjust the effect level, room size, and liveness. To adjust these parameters, use the buttons and controls on the front panel.
1. Press SURROUND MODE | SURROUND |
repeatedly until “LARGE | MODE |
|
THEATER (or DIG L. THEATER, DTS L. THEATER)” or “SMALL THEATER (or DIG S. THEATER, DTS S. THEATER)” appears on the display.
SOUND |
1)Press BALANCE/SURROUND ADJUST repeatedly until “EFFECT LEVEL” appears on the display.
The display changes to show the current setting.
2)Turn MULTI JOG to select the effect level.
•As you turn it, the effect level changes as follows:
BALANCE/SURROUND
ADJUST
MULTI JOG
2. | Press SOUND. |
| |||
| The 10 keys are activated for sound adjustments. | ||||
3. | Press TEST to check the speaker | TEST | |||
| output balance. | ||||
| 10 | ||||
| “TEST TONE L” starts flashing on the | RETURN | |||
| display, and a test tone comes out of the |
| |||
| speakers in the following order: |
| |||
| TEST TONE L TEST TONE C | TEST TONE R | |||
|
|
|
|
|
|
EFFECT 1 EFFECT 2 EFFECT 3
EFFECT 5 | EFFECT 4 |
As the number increases, the overall level of reflections applied to the direct sounds increases. (Normally set it to “EFFECT 3.”)
| (Left front speaker) | (Center speaker) | (Right front speaker) | ||||
|
| TEST TONE LS |
| TEST TONE RS | |||
|
| (Left rear speaker) |
|
| (Right rear speaker) |
|
Continued to the next page.
37