JVC RX-9000VBK manual Digital Input Digital in Terminal Setting, OPT. DIG. in appears on Display

Digital Input (DIGITAL IN) Terminal Setting

When you use the digital input terminals, you have to register what components are connected to which terminals (DIGITAL IN 1/2/3/ 4).

Before you start, remember...

•There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

When the DIGITAL 1 is set to “CDR”

2 CD 3 TV (or 4 DBS*) 4 DVD Ò 2 CD 3 TV (or 4 DBS*) 4 MD Ò 2 CD 3 MD 4 DVD Ò

2 MD 3 TV (or 4 DBS*) 4 DVD Ò (back to the beginning)

When the DIGITAL 1 is set to “TV” or “DBS”

2 CD 3 DVD 4 CDR	Ò	2 CD 3 DVD 4 MD Ò
2 CD 3 MD 4 CDR	Ò	2 MD 3 DVD 4 CDR Ò
(back to the beginning)

On the front panel ONLY:

To set the DIGITAL 1 terminal

SETTING

When the DIGITAL 1 is set to “CD”

1.Press SETTING repeatedly until “COAX. DIG. IN” appears on the

display.

The display changes to show the current setting.

MULTI JOG

2.Turn MULTI JOG to select the appropriate digital terminal setting.

• As you turn it, the display changes to show the following:

1 DVD Ò1 MD Ò1 CDR Ò1 TV (or 1 DBS*) Ò 1 CD Ò(back to the beginning)

*If you have changed the source name from “TV SOUND” to “DBS,” “DBS” appears.

To set the DIGITAL 2/3/4 terminal

1. Press SETTING repeatedly until		SETTING
“OPT. DIG. IN” appears on the
display.
The display changes to show the current setting.
	DIGITAL 3 terminal setting

DIGITAL 2 terminal setting DIGITAL 4 terminal setting

2. Turn MULTI JOG to select the	MULTI JOG
appropriate digital terminal

settings.

•As you turn it, the display changes to show the following:

When the DIGITAL 1 is set to “DVD”

2 CD 3 TV (or 2 DBS*) 4 CDR Ò 2 CD 3 TV (or 2 DBS*) 4 MD Ò 2 CD 3 MD 4 CDR Ò

2 MD 3 TV (or 2 DBS*) 4 CDR Ò (back to the beginning)

When the DIGITAL 1 is set to “MD”

2 CD 3 TV (or 2 DBS*) 4 CDR Ò

2 CD 3 TV (or 2 DBS*) 4 DVD Ò 2 CD 3 DVD 4 CDR Ò

2 DVD 3 TV (or 2 DBS*) 4 CDR Ò (back to the beginning)

2 DVD 3 TV (or 3 DBS*) 4 CDR Ò 2 DVD 3 TV (or 3 DBS*) 4 MD Ò 2 DVD 3 MD 4 CDR Ò

2 MD 3 TV (or 3 DBS*) 4 CDR Ò (back to the beginning)

*If you have changed the source name from “TV SOUND” to “DBS,” “DBS” appears.

Note:

When shipped from the factory, the DIGITAL IN terminals can be used as the digital input for the following components.

•DIGITAL 1 (coaxial): For DVD player

•DIGITAL 2 (optical): For CD player

•DIGITAL 3 (optical): For digital TV broadcast tuner

•DIGITAL 4 (optical): For CD recorder

Selecting the Analog or Digital Input

Mode

When you have connected digital source components using the digital terminals (see page 9), you need to change the input mode for these components to the appropriate digital input mode correctly — AUTO/PCM, DOLBY DIGITAL, or DTS.

Before you start, remember...

•The digital input (DIGITAL IN) terminal setting should be correctly done for the sources you want to select the digital input mode for. Without setting this digital input terminal correctly, you cannot change the input mode from analog input to digital input even if you follow the procedure below.

•The digital input can be used for the main room sources. The analog input is always selected as the sub-room source without respect to this setting.

On the front panel:

1. Turn SOURCE SELECTOR until	SOURCE SELECTOR
the source (CD, MD, TV SOUND,
DBS, DVD, or CDR/VCR2)* for
which you want to change the
input mode appears on the display.

Note:

*Among the sources listed above, you can select the digital input only for the sources which you have selected the digital input terminals for. (See “Digital Input (DIGITAL IN) Terminal Setting.”)

26