48 EN |
| TROUBLESHOOTING (cont.) | |||||||
|
|
|
|
|
|
|
|
|
|
| EDITNG |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
| SYMPTOM |
| POSSIBLE CAUSE |
|
| CORRECTIVE ACTION |
| ||
| 1. Recording will not start, and [CASS] |
| ● There is no cassette loaded. |
| Insert a cassette. |
|
| ||
| blinks on the front display panel for |
| ● The loaded cassette has had its record |
| Remove the cassette and cover the hole |
| |||
| about 5 seconds. |
| safety tab removed. |
| with adhesive tape, or load a cassette |
| |||
|
|
|
|
| on which the record safety tab is in- |
| |||
|
|
|
|
| tact. |
|
|
|
|
|
|
|
|
|
|
| |||
| 2. |
| ● The components have been incor- |
| Connect the components correctly |
| |||
|
|
| rectly connected, or correct video |
| ( page 5, 6) or check “REAR AUX L- |
| |||
|
|
| connector ([S VIDEO] or [VIDEO]) is |
| 1 (or |
| |||
|
|
| not selected. |
| ting ( page 38). |
|
| ||
|
|
| ● The power to one or more of the units |
| Make sure the power to all units is on. |
| |||
|
|
| has not been turned on. |
|
|
|
|
|
|
|
|
| ● The recordingVCR’s input location has |
| Select the appropriate input location on |
| |||
|
|
| been set incorrectly. |
| the recording VCR. |
|
| ||
|
|
|
|
|
|
|
|
|
|
| VIDEO NAVIGATION |
|
|
|
|
|
|
|
|
| SYMPTOM |
| POSSIBLE CAUSE |
|
| CORRECTIVE ACTION |
| ||
| 1. Tape information screen does not ap- |
| ● The current tape inserted has not been |
| Tape information cannot be shown if it |
| |||
| pear for the currently inserted tape. |
| recorded on this VCR. |
| has not been recorded on this VCR. |
| |||
|
|
|
|
|
|
| |||
| 2. The VCR cannot search for the de- |
| ● Two (or more) tape numbers are re- |
| Video Navigation cannot work correctly |
| |||
| sired program. |
| corded on one tape. |
| on a tape if it has more than one tape |
| |||
|
|
|
|
| number. If this happens, |
| |||
|
|
|
|
| tape up to its end, eject it, and try it |
| |||
|
|
|
|
| again. |
|
|
|
|
|
|
| ● The inserted program is not recorded |
| It is impossible to search the desired |
| |||
|
|
| on this VCR. |
| program which is not recorded on this |
| |||
|
|
|
|
| VCR using Video Navigation. |
|
| ||
|
|
|
|
|
|
|
|
|
|
| 3. “MEMORY FULL” appears on the |
| ● The VCR’s memory for Video Naviga- |
| Check | the | remaining | memory |
|
| screen when you try to start record- |
| tion is fully recorded. |
| ( page 34). If it is full, delete unnec- |
| |||
| ing. |
|
|
| essary Video Navigation information |
| |||
|
|
|
|
| ( page 33, 34). |
|
| ||
|
|
|
|
|
|
|
|
|
|
| 4. The information data for Video Navi- |
| ● The VCR’s memory for Video Naviga- |
| Check | the | remaining | memory |
|
| gation is not registered. |
| tion is fully recorded. |
| ( page 34). If it is full, delete unnec- |
| |||
|
|
|
|
| essary Video Navigation information |
| |||
|
|
|
|
| ( page 33, 34). |
|
| ||
|
|
| ● “NAVIGATION” is set to “OFF”. |
| Set “NAVIGATION” to | “ON” |
| ||
|
|
|
|
| ( page 25). |
|
|
| |
|
|
| ● The recording time is not enough. |
| For details on the recording time for |
| |||
|
|
|
|
| Video Navigation, refer to ‘NOTES’ on |
| |||
|
|
|
|
| page 24. |
|
|
| |
|
|
|
|
|
|
|
|
|
|
