DVD DIGITAL THEATER SYSTEM
Simplified connection manual
English | Please see INSTRUCTIONS from page 6 to page 10 as well. |
Installation
Example
Satellite speaker | Center speaker |
(front left stpeker) |
TV
To attach non-slip rubbers to the center speaker
Attach the supplied
The
FM and AM antenna terminals (6)
Digital input and | |
input terminals (6, 8, 9) | output terminals (9) |
Please see the reverse page.
Connect to the TV if it has an
Powered sub-woofer
Center unit
before applying.
Attach
Attach two rubbers at left and right at the front of the speaker, and one in the middle at the rear.
Non-slip rubber
quality). Connect the cables with the £ mark facing down.
Satellite speaker (rear left speaker)
The rear speakers are
Satellite speaker (front right speaker)
CAUTIONS:
• For safety reasons, always ensure that there is sufficient place behind
1 cm (7/16”) 5 cm (2”)
Front side
| COMPU LINK | AC power cord (supplied) (10) | |
Analog audio input and output terminals (8, 9) | terminals (52, 54) | Before plugging the center unit | |
VIDEO OUT SELECT (7) | into an AC outlet, make sure that | ||
| |||
| all connections have been made. | ||
|
|
placed behind the listening position.
Satellite speaker (rear right speaker)
the powered sub-woofer.
• If the front and rear speakers are placed on the floor, always ensure that they are level.
Bottom
To connect speakers (7)
Connect the satellite speakers and center speaker to the terminals on the powered subwoofer using the speaker cords supplied. Labels are attached to the speaker cords to indicate the speaker and terminal to which each is to be connected.
•The four satellite speakers may be used at either front or rear.
•Ensure that the left and right speakers are connected to left and right respectively, and that they are connected with the correct polarity (+ve,
Twist and remove | Center speaker |
the insulation at the |
|
end of each speaker |
|
cord. |
|
|
| Video cable (supplied) (6) | |
|
| Connect the MONITOR OUT | |
Ensure that | Yellow | terminal to composit video | |
input terminal on the TV. | |||
| |||
the £ mark |
|
| |
on the plug |
| Yellow | |
faces upwards. |
|
System cable (supplied) (6) |
| |
Connect the center unit to | ||
| ||
powered sub woofer. |
|
Ensure that the £ mark on the plug faces to the right.
To hang satellite speakers from the wall
Use the supplied bracket to fix satellite speakers to the wall.
CAUTION: ATTACHING THE BRACKETS ON THE WALL
When attaching the brackets on the wall, have them attached to the wall by a qualified person.
DO NOT attach the brackets on the wall by yourself to avoid an unexpected damage of their falling from the wall, caused by incorrect attachment or weakness in the wall.
Location of attachment to wall:
Care is required in selecting a location for attaching satellite speakers to the wall. Injury to personnel, or damage to equipment, may result if the speakers are attached in a location which interferes with daily activities.
Attaching speakers to the bracket
Audio channel display lamp
Uses lamps to display the audio channel configuration for the disc currently playing.
• The audio channel display lamp is not an indicator of which speakers are producing sound.
The lamps refer to the speaker channel as follows.
L:Left front speaker channnel
R:Right front speaker channel
C:Center speaker channel
RS: Right surround speaker channel
Front right speaker | Front left speaker |
Speaker cord (6 m)
(19.7 ft)
White
Black
Rear right | Rear left |
|
|
speaker | speaker |
| To AC outlet |
|
|
| |
|
| Note: | Before plugging the powered sub woofer |
|
| into an AC outlet, make sure that all | |
|
| • Mixing up the polarity | |
|
| connections have been made. | |
|
| of the speaker cords | |
|
|
| |
|
| can reduce the stereo |
|
Speaker cord |
| effect and sound |
|
(15 m) (49.2 ft) |
| quality. |
|
EN, FR | J C 0900TNMNATJSC |
V |
1. Use the screw supplied to attach the speaker to the bracket.
Bracket
Screw
2. Adjusting the angle of the satellite speakers
The angle of the speaker may be adjusted in the
When adjusting the angle, loosen the screw slightly, make the adjustment, and then tighten the screw firmly.
Tilting the speaker to the front
CAUTION:
If the screw is not tightened firmly, it may cause injury to personnel or damage to equipment.
Tilting
LS: Left surround speaker channel
S:Rear speaker channel (monaural) LFE: Sub woofer channel
The lamp display indicates the type of disc (DVD or CD) currently playing as follows.
Example:
With Dolby Digital 5.1 ch, DTS Digital 5.1 ch, or MPEG Multichannel 5.1 ch surround
With Dolby Digital (Lt/Rt)
With stereo sound (eg Audio CD)
When playing DVD recorded in Dolby Digital, Dolby Pro Logic, DTS, or MPEG Multichannnel Surround Sound, set the main system surround mode to “SURROUND ON.”
When it is set to “SURROUND OFF” the audio channel display lamp will not change. However, sound will be played without surround effects (see page 21).
