Version 1.08 (04/07)Manual: CMOS Industrial Camera LOGLUX® i5
⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯
Example: | w $14C #1 | ;permanent precharging |
PROFILE_DESCRIPTION
The register contains a string of 32 ASCII characters that identify the profile.
Function group ‚Working parameters‘This function group provides various camera service registers, among them registers specifying the firmware of the camera as well as functions for setting the trigger register, for initializing and copying camera profiles, and for reading a temperature sensor inside the camera. Please note that these registers are volatile, i.e. the register values are not saved when the power is turned off.
Register |
| Address | Format | Description |
| Value range | Meaning | Access |
PARAM_VERSION |
| $900 | 1 long | Firmware version |
|
|
| read only |
PARAM_EVENT |
| $904 | 1 byte | Event generation for trigger |
| Write access releases a trigger |
| |
|
|
|
| and switchport |
| $01 | signal, switchport 1 event or | write |
|
|
|
|
|
| $02 | switchport 2 event | only |
|
|
|
|
|
| $04 |
|
|
PARAM_INITPROFILE |
| $905 | 1 byte | Initializes a profile |
| $1x ... 4x | Initializes profile 1 ... 4 with the | write |
|
|
|
|
|
|
| Init values for | only |
|
|
|
|
|
| $x1 | Single integration slope mode |
|
|
|
|
|
|
| $x2 | Dual integration slope mode |
|
|
|
|
|
|
| $x3 | Quadr. integration slope mode |
|
PARAM_COPYPROFIL |
| $906 | 1 byte | Copies a profile |
| $1x ... $8x | Target profile 1 ... 4 | write |
|
|
|
|
|
| $x1 ... $x8 | Source profile 1 ... 4 | only |
PARAM_TEMP0 |
| $908 | 1 word | Temperature sensor 0 |
| 218 .. 398 | Temperature in [Kelvin] | read only |
PARAM_TEMP1 |
| $90A | 1 word | Temperature sensor 1 |
| 218 .. 398 | Temperature in [Kelvin] | read only |
Table 6 : Registers of function group 'Working parameters' |
|
|
|
| ||||
PARAM_VERSION | This register allows the camera to be identified from the host register. |
| ||||||
PARAM_EVENT | Events can be generated in the camera by entering data in this register. | |||||||
|
| These events are sent to various modules such as the trigger or switchport | ||||||
|
| module. Functions can be triggered in the respective module if the event | ||||||
|
| register had been specified in the module's event source parameter. Example: | ||||||
|
| If | the value $04 (event | register) had been entered in | register | |||
PROFILE_TRGSOURCE, a write access to register PARAM_EVENT using the value $01 will trigger a framegrabbing process. This could be done to simulate the response of the camera to an external trigger signal.
PARAM_INITPROFILE
The register permits the factory (default) settings of camera profiles 1 to 4 to be reset. The register content of the respective target profile will be irrevocably overwritten by the register content of the source profile.
Example: | w $905 | $13 | ;initializes P1 with P3 |
PARAM_COPYPROFILE
The register permits camera profiles 1 to 8 to be given identical register contents. The register content of the respective target profile will be irrevocably overwritten by the register content of the source profile.
Example: | w $906 | $62 | ;copies Profil2 to Profil6 |
Page 36 of 46 | KAMERA WERK DRESDEN GmbH |