Kamera Werk Dresden CMOS Technical specification, Technical data of the LOGLUX i5 CL (survey), Pin assignments of the LOGLUX® i5 CL, Front view, Pin 2: GND, 'DIGITAL OUT, Power supply:

Version 1.08 (04/07)Manual: CMOS Industrial Camera LOGLUX® i5

⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯

Technical specification

Technical data of the LOGLUX i5 CL (survey)

Sensor format:	1280 x 1024 pixels
	(2/3 in. sensor diagonal)
	freely selectable ROI
Pixel size:	6.7 x 6.7μm2
ADC resolution:	10 bit greyscale value
Image transfer	Resolution	fps
rate:	1280 x 1024	36
	1024 x 768	58
	320 x 240	445
Shutter modes:	rolling shutter
	central shutter
Dynamic range:	64 dB linear,
	> 100 dB in multiple
	integration slope mode
FPN:	< 0.2% RMS
Sensitivity:	8.46 V/(lx . s)
	in visible light and NIR
	range (70 lx = 1 W/m2)
S/N ratio:	1600 : 1
Spectral range :	400...1000 nm
Configuration:	- 4 user-programmable camera profiles
	- bootable with initial settings

Integral functions: test image, three user-programmable LUTs, optional: target graticule, pixel binning, real-time matrix operations, etc.

Interfaces: - CameraLink™(base)

-RS-232 115kbaud, electrically isolated

-one 24VDC trigger port, electrically isolated

-two 24VDC/max. 500mA switchports (low-side switch), electrically isolated

Power supply:	18...35 VDC
Power loss:	<2 W
Temp. range:	0...60°C (operation)
Dimensions HxWxD	54 x 46 x 82
(mm/without lens):
Lens mount:	C mount
Weight:	approx. 250g (without lens)
Scope of delivery:	camera with LuxWare software and
	manual (on CD-ROM)

Pin assignments of the LOGLUX® i5 CL

The mechanical and electrical parameters of the CameraLink™ connector ('DIGITAL OUT') correspond to the CameraLink™ standard specifications. More information can be found in the following documents and under www.ieee.org :

∙CameraLink™ Interface Standard Specification, Technical Communications, October 2000

∙CameraLink™ Technology Brief, Basler Vision Technologies, March 2001

Assignment of pins of the 9-pole support connector ('COM / POWER / TRIG'):

Front view	Pin	Signal name	Function
	no.
	1	+24V	24V power supply
	2	Rx	Serial reception
	3	Tx	Serial transmission
	4	GND_pwr	Central ground (power
			supply)
	5	GND_if	Serial signal ground
	6	Ext_Trig_in	Trigger signal input
	7	GND_pwr	Central ground (trig./SW)
Fitting female connector (example):	8	Ext_SW_out1	1st switch signal output
	9	Ext_SW_out2	2nd switch signal output
product name: JEZ-9S made by JST

Pin assignment of the split cable for the LOGLUX® i5 CL

Power supply:	Binder 2-pin conn. → Binder 2-pin female c. type 712 (Order no. 99-0402-00-02)
	Pin 1: +24VDC	Pin 2: GND
Trigger input/
switch outputs:	Binder 4-pin conn. → Binder 4-pin female c. type 712 (Order no. 99-0410-00-04)
	Pin 1: Trigger input	Pin 2: Switchport 0 Pin 3: Switchport 1 Pin 4 : GND

Page 40 of 46 KAMERA WERK DRESDEN GmbH