SECTION 5

SERVICE TECH INFORMATION

5B.ROTARY VALVE SERVICE

Before working on the valve, turn off the water supply and disconnect from electrical power. TO

RELIEVE PRESSURE:

-- 3 VALVE BYPASS: Close the inlet valve and open a soft water faucet. Then close the outlet valve and open the bypass valve.

-- SEARS SPECIAL BYPASS: Slide the bypass valve stem to bypass position. Loosen 3 hex head screws toward the back side of the valve to allow pressure water to bleed out. Catch water with a rag.

DISASSEMBLY

To remove a part or group of parts, refer to the valve drawing. A common screwdriver or nut driver, Phillips screwdriver and pliers are the only tools needed to completely disassemble.

SERVICING THE VALVE

Inspect all o-rings, seals and gaskets for wear or defects.

Inspect the bottom surface of the rotor for scratches, chips or wear.

NOTE: If replacement is needed, be sure to use the current replacement part.

ASSEMBLY

Be sure all parts are in place and in the proper position. Lubricate ALL o-rings and seals with FDA approved silicone grease. To install the rotor seal, first place the seal into the valve groove, rounded side down (see cross-section). Apply a light coating of silicone grease to the seal’s crossing ribs. Then, carefully center the wear strip on the seal, and push it downward onto the seal.

motor

motor plate

cam & gear

switch

o--ring seals

wave washer

bearing, wave washer

wear--strip

seal

sensor housing

See

Nozzle

assembly service, page 17

assembled

view

flow plug assembly

rotor

o--ring seal

rotor seal

drain seal

nozzle & venturi seal

turbine support turbine

Install the nozzle and venturi seal and drain seal. Assemble wave washer bearing, the wave washer, and 2 o-rings onto the rotor top shaft. Then center the rotor in the valve body, on the rotor seal.

Lower the cover onto the valve body and rotor shaft. Then install the cover holding screws. Before tight- ening the screws, install the valve cam and gear. Then, turn the rotor (clockwise only) to service position. Tighten the screws using a criss-cross pattern. If a torque wrench is available, torque to 30-40 inch pounds.

Lubricate the gear on the motor, and the valve cam gear with Molykote grease, or other high qualitygear lubricant.

Be sure to orient switch as shown, with lever toward the cam.

25

Page 24 Page 26
Page 25
Image 25
Kenmore 625.348670 Service Tech Information 5B.ROTARY Valve Service, Disassembly, Servicing the Valve, Assembly
Page 24 Page 26

625.348670 specifications

The Kenmore 625.348670 is a portable dehumidifier designed to improve indoor air quality and provide a comfortable living environment. It is particularly effective in combating excess moisture in homes, especially in areas prone to high humidity such as basements, bathrooms, and laundry rooms.

One of the main features of the Kenmore 625.348670 is its capacity to remove up to 50 pints of moisture from the air per day. This high extraction rate is suitable for rooms up to 4,500 square feet, making it ideal for both residential and commercial applications. The unit is equipped with a built-in humidistat that allows users to set their desired humidity level, automatically turning the dehumidifier on and off as needed to maintain optimal conditions.

The dehumidifier features a user-friendly control panel, complete with an LED display that shows the current humidity level and settings. It also has several operational modes, including continuous operation, allowing for the option of continuous drainage via a drain hose—ideal for areas with persistently high humidity levels. The 625.348670 is designed with convenience in mind, featuring an easy-to-remove water tank for manual drainage when continuous drainage is not an option.

The Kenmore 625.348670 employs advanced technologies for efficient moisture extraction. Its compressor system operates quietly, ensuring minimal disruption in your living space. This unit also emphasizes energy efficiency, working to reduce energy consumption while still effectively controlling humidity levels, which can be a significant advantage in lowering energy bills.

Another characteristic to note is its portability. The unit is designed with built-in handles and caster wheels, allowing easy movement from room to room. Additionally, its compact design ensures it can fit into tighter spaces without sacrificing performance.

Overall, the Kenmore 625.348670 is an excellent solution for anyone looking to control humidity levels in their environment. With its robust design, high moisture removal capacity, user-friendly features, and energy efficiency, it stands as a reliable choice for managing indoor air quality effectively.
Top Page Image Contents