DC-DC Converter | Kenwood TH-K2ET, TH-KAE, TH-K4AT, TH-K2AT specification

CONNECTING TO A CIGARETTE LIGHTER SOCKET

To connect the transceiver to the cigarette lighter socket in your vehicle, use an optional PG-3J Cigarette Lighter cable.

When the PG-3J is connected to the cigarette lighter plug, the transceiver automatically starts charging the PB-43N Ni-MH battery pack. While you operate the transceiver, it charges the PB-43N Ni-MH battery pack in the background.

To connect with an external 24 V power source via a DC-DC converter, only use the optional PG-3J Cigarette Lighter cable. Using the PG-2W DC cable in this situation may cause a fire.

2 4 V

2 4 V

2 4 V

DC-DC Converter

PG-3J 1 2 V

Socket

1 2 V	PG-3J

DC-DC Converter

1 2 V PG-2W

Note:

◆Do not use the PG-2W to connect a vehicle battery (12 V) directly. Extensive voltage could result in damaging the transceiver.

◆If the input voltage exceeds approximately 16.5 V, warning beeps sound and “DC ERR” appears.

8

Image 22

Kenwood TH-K2ET, TH-KAE, TH-K4AT, TH-K2AT instruction manual DC-DC Converter

Contents

TH-K2AT TH-K2E TH-K2ET Page Models listed below are covered by this manual TH-K2AT, TH-K2E, TH-K2ET TH-K4AT, TH-K4E Precautions Contents Call Channel Iii Optional Accessories Operation Notices Thank YOU Quantity Accessory TH-K2AT Quantity TH-K2ET TH-K4AT TH-K4E KEY 1 s Instruction What to DoKEY1, KEY2 KEY1+KEY2 Preparation Installing Alkaline Batteries Insert or remove six AA LR6 Alkaline batteries Strap Installing the Belt Clip Other than TH-K2AT K2/ M2, TH-K4AT M2 Plug the charger into an AC wall outletPage DC-DC Converter Fuses 4 a Your First QSO Page Getting Acquainted TH-K2AT/ ET/ K4AT TH-K2E/ K4E E r t y ui o !0 !1 3!2 Page Page Press Power briefly to switch the transceiver power on Switching the Power ON/OFFAdjusting the Volume To switch the transceiver OFF, press Power again Turn the Tuning control to adjust the level Adjusting the SquelchPress F, MONI/SQL When you finish speaking, release PTT Selecting an Output PowerTransmitting Selecting a Frequency VFO Mode MHz Mode Example To enter 145.750 MHz Key Display 5 5 To enter 145.000 MHz Key Display To change 144.650 MHz to 145.650 MHz Key Display 4 5 To change 144.650 MHz to 145.650 MHz Key Display Example 5 Short cutTo change 145.200 MHz to 145.750 MHz Key Display Turn the Tuning control to select your desired Menu Menu SetupPress Menu Page Function Selections Display Tuning control DTMF.MR ARO2 ON/ OFF BCL CK1 PRI ON/ OFF Operating Through Repeaters Programming an Offset Selecting an Offset Direction Press Menu to store the setting or PTT to cancel Selecting an Offset Frequency Activating the Tone Function Turn the Tuning control to select Menu No T.CT.DCSPress Menu Appears when the Tone function is on Selecting a Tone Frequency Available Tone Frequencies Tone Frequency Hz TH-K2E/ ET/ K4E only TH-K2AT K/ K2 only TH-K2E/ K2ET only Appears when the function is on Press F, Menu 1 s to switch the function on or OFF Press Menu 1 s Memory Channels Odd-split channels allow Parameter Simplex Odd-Split Data listed below can be stored in each memory channelYes DCS code Storing Simplex Frequencies or Standard Repeater Frequencies Storing Odd-Split Repeater Frequencies Press PTT+MR Recalling a Memory Channel Using the Tuning Control Press MR to enter Memory Recall Mode Press MR to clear the channel data Blinking cursor appears Repeat steps 5 and 6 to enter up to 6 digits Memory \ VFO Transfer Channel \ Channel Transfer Channel 0 ~ Channel 0 ~ L0/U0 ~ L2/U2, Pr, AL1 Recalling the Call Channel Press Call to recall the Call Channel Press F, Call Reprogramming the Call ChannelPress PTT+CALL Weather Alert TH-K2AT K/ K2 only Programming the Weather Radio Frequency Enabling a Weather Alert Press PTT+MR+ Power While transmitting Lamp Menu CALL1 Tuning control2 Tuning controlThen Scan Type Purpose ScanScans the Call channel Band Scan Storing a Program Scan Frequency Range Program ScanPress VFO Performing Program Scan Press MR to store the end frequency in the memory channel Press MR 1 s All-Channel ScanTo stop All-Channel Scan, press MR or PTT Call Scan Programming Priority Channels Using Priority Scan To quit Priority Scan, select OFF in step Icon disappears Carrier-Operated Mode Time-Operated Mode defaultSeek Mode Using Ctcss Selective Call Press Menu and turn the Tuning control to select Menu No CT Selecting a Ctcss Frequency Press Menu to store the new setting or PTT to cancel Available Ctcss Tone Frequencies Ctcss Freq. ID Scan Using DCS DCS Press Menu to store the new code or PTT to cancel Selecting a DCS Code DCS Code ID Scan Dtmf Functions Freq 1209 1336 1477 1633 Dtmf TX Hold TH-K2AT/ ET/ K4AT only Storing a Dtmf Number in Memory Turn the Tuning control to select a Dtmf code Transmitting a Stored Dtmf Number Adjusting the Dtmf Tone Transmission Speed Adjusting the Pause Duration Dtmf KEY Lock APO Auto Power OFF Operator Conveniences Battery Output Operating Time Hours Approx PB-43N 11.0 10.0 BT-14 10.5 Release PTT to exit Beat Shift Busy Channel Lockout KHz 12.5 kHz ModelFreq. Step Size 25 kHz Press F 1 s To illuminate the display and keys Press LampTo keep the light on continuously Press F, Lamp Press F 1 s to unlock the keys Tuning Control Unlock Tuning2 + KEY Function Release MONI/SQL to return to normal operation Turn the Tuning control to select a character Repeat steps 4 and 5 to enter up to 6 digits Current programmable frequency range for the band appears Upper limit frequency blinks TX Power To change the transmission output power, press F, PTT Battery Output Output Power Approx BT-14 PB-43N 13.8 VOX Gain To turn OFF the VOX function, select OFF in stepPage VOX Delay Time VOX on Busy Clip Microphone with Headset with VOX/ PTT Earphone Optional AccessoriesBC-21 BT-14 Battery Charger Battery Case 6 AA/ LR6 KHS-21 KSC-24 Headset Rapid Charger SMC-32 DC Power Cable Cigarette Lighter PowerPB-43N PC Interface Cable Speaker Microphone SMC-33 SMC-34 Interfacing to Peripherals SP/MIC Jack 105 Using the PG-4Y PC Interface Cable Using the MCP-1A Software Turn the Tuning control to select Menu No PC Troubleshooting Service Service Note Cleaning Full Reset Initial SettingsVFO Reset Press F+ Power Performing ResetPress F to reset the transceiver Press VFO to reset the transceiver Reset using the Menu Press Menu to reset the transceiver Receiving Signals in Cities Operating Voltage Transmission Internal Beats Problem Solution 118 119 120 140.800 MHz, 153.600 MHz, 166.400 MHz 168.350 MHz 453.250 MHz Specifications General 123 Transmitter Receiver TH-K2E TH-K2ET 127 128 129 TH-K4AT TH-K4E 131 132 133 Index 106 ClearingDCS Menu No 116 Installing111 Menu 101 Offset115 107 112 ResetReprogramming 113 108 VolumeTone VOX Voice-Operated Transmission