14 CONNECTING PERIPHERAL EQUIPMENT

DX PACKETCLUSTER TUNE

If you have a TM-D700 transceiver, you can connect the TM-D700 to the TS-480 transceiver to use the DX PacketCluster Tune function. Connect the 2 transceivers with a cross-wired RS-232C cable as shown below. Configure the TM-D700 transceiver to the DX PacketCluster node frequency.

TS-480 transceiver

TM-D700 transceiver

EXT.SP

DATA

REMOTE

MIC

 

 

 

PANEL

 

 

 

 

COM

PADDLE

KEY

 

COM

 

DATA

 

GPS

PANEL

 

 

MIC

RESET

Cross-wired cable

1Press [MENU/ F.LOCK] and turn the MULTI control to select Menu No. 56 on the TS-480 transceiver.

2Press []/ [] to select the same communication baud rate configured on the TM-D700 transceiver.

3Tune to the DX PacketCluster node frequency on the TM-D700 transceiver.

4Press [F] (1 s), [TNC] on the TM-D700 transceiver.

“TNC APRS” appears on the TM-D700 transceiver.

5Press [F] (1 s), [DX] on the TM-D700 transceiver.

6Select a desired DX station data with [c]/ [d] on the TM-D700 transceiver.

7Press [MHz] on the TM-D700 transceiver to transfer the frequency data to the TS-480 transceiver.

If the transferred frequency data is available on the TS-480 transceiver, the frequency data will be overwritten to the current operating frequency. Otherwise, the operating frequency of the TS-480 transceiver remains unchanged.

For more detailed operation on the DX PacketCluster operation of the TM-D700 transceiver, refer to page 6 of the TM-D700 instruction manual (Specialized Communications).

Note: The firmware of the TM-D700 transceiver must be version G2.0 or later to use the DX PacketCluster Tune function.

CROSSBAND REPEATER

If you have a TM-D700 transceiver, you can connect the TM-D700 transceiver to the TS-480 transceiver to use the Crossband repeater function. Connect the 2 transceivers with a mini DIN cable (6-pin) as shown below.

TS-480 transceiver

TM-D700 transceiver

EXT.SP

DATA

REMOTE

MIC

 

 

 

PANEL

 

 

 

 

COM

P

KEY

To DATA connector

COM

 

DATA

 

GPS

PANEL

 

 

 

MIC

RESET

To DATA connector

After connecting the 2 transceivers with the cable, access Menu No. 57 (DTS polarity) on the TS-480 transceiver and select “on”. You will further need to adjust the audio input/ output level of the TS-480 transceiver using Menu Nos. 46 and 47.

 

 

 

TS-480

TM-D700

t

 

y

ANI q

 

 

PKD

 

q

 

 

 

 

 

 

 

ANG w

 

w

DE

 

 

 

 

e

 

r

DTS e

 

e

PKS

 

 

 

NC r

 

r

PR9

 

 

 

ANO t

 

t

PR1

q

 

w

SQC y

 

y

SQC

 

 

 

 

 

 

Mini DIN

Mini DIN

Mini DIN

6-pin male

6-pin male

6-pin male

79

Page 87
Image 87
Kenwood TS-480SAT, TS-480HX instruction manual DX Packetcluster Tune, Crossband Repeater