Expansive Application Software | Kenwood TS-590S specs

8 EXPANSIVE APPLICATION SOFTWARE

8.1 Windows Related Software

This chapter describes the Windows related software to be used to control the TS-590S from a PC. Following are the Windows related software products that can be used with the TS-590S.

		Table 8-1 Windows Related Software for TS-590S

	Name	Description

	ARCP-590	This software enables control of the TS-590S from a PC.

	ARHP-590	This host program is used on the host station PC when the TS-590S is remotely controlled over
	ARHP-590	a network. The software is used in combination with ARCP-590.


		This VoIP software is to transfer the TX and RX audio signals when remotely controlling the
	ARVP-10	TS-590S over a network.
		Note: The software is composed of ARVP-10H and ARVP-10R.

		This software enables use of the microphone and speaker of a PC in place of those on the
		TS-590S. It enables the audio signal from the PC’s microphone to be transfered via USB audio
		and transmitted from the TS-590S. Also, the audio output of the TS-590S can be emitted from
	ARUA-10	the PC’s speaker via USB audio.
	ARUA-10	Note:
		Note:
		 If you are using a home-made audio cable connected to the ACC2 connector, this software is not
		required.
		 This software is not required if this is used over a network.

	Virtual COM Port	Being installed on the PC, this supports use of ARCP-590 and ARHP-590 after the TS-590S is
	Virtual COM Port	connected to a PC with a USB cable.
	Driver	Note: If the TS-590S is connected to the PC with a serial cable, this software is not required.

8.2 System Configurations

We will provide some typical system configurations using the TS-590S and Windows software.

8.2.1 Controlling TS-590S from a PC using the COM Connector

The microphone connected to the TS-590S and the transceiver’s built-in speaker are used.

	PC			Type of	TS-590S
	Software		Hardware	Connection	Hardware

Control signal	ARCP-590		-	RS-232C cable	* Connected to the COM connector

					The microphone connected to the
Audio signal	-		-	No connection	TS-590S and the transceiver’s built-in
					speaker

52

CONTENTS

TS-590S

Image 58

Kenwood TS-590S manual Expansive Application Software, Windows Related Software, System Configurations

Contents

TS-590S About Trademarks and Intellectual Properties About CopyrightCopyright of this Manual and Software Other Restrictions Contents Optional Accessory Product Planning Objectives Development Spirit Reception Type of Conversion Reception Block diagram Down Conversion Down Conversion MCF Hints and Tips Comparison of Bandpass Characteristics of MCFs Measurement Conditions Up Conversion Dynamic Range in the 50 MHz Band RX Auxiliary Circuits CN101 CN102 CN103 If Circuits TransmissionKenwood Traditional Transmitting Circuitry FET Final Circuit Transmission Remote Connector High-speed Relay-controlled Antenna Tuner Menu N o or N o 1 or DRV Terminal Transmission Output Characteristics of DRV Terminal at 136 kHz and 0 dBm Transmission Comparison C/N Characteristics Local Oscillator DSP Multipurpose 32-bit Floating Point DSP Advanced AGC Control via if Digital Processing DSP Control Block Diagram of IF-AGC Interference Elimination Within AGC Loop Digital if Filter Types of Digital if Filters LOW CUT Manual Notch Filter and Auto Notch Filter Digital Noise Blanker NB2 Demodulation Modulation Beat Cancel AF Processing DSP-based Auxiliary Circuits for RX Noise Blanker NB2 if Processing Overview of Noise Reduction 11 NB2 Inactive 4 NR1 Spectral Subtraction Method AF Processing 13 Conceptual Scheme of NR1 Based on Spectral Subtraction Audio spectrum components swamped by noise 5 NR1 Based on a Line Enhancer AF Processing 16 NR1 Line Enhancer Method Inactive 6 NR2 AF Processing 18 NR2 Inactive DSP-based Auxiliary Circuits for TX Speech Processor AF Processing DSP-based Auxiliary Circuits Common to TX/RX TX Equalizer & RX Equalizer AF Processing Software Enhancing Operating Pleasure Extended Data-mode Related Functions Drive Out Software Enhancing Operating Pleasure Single Button Toggles if Filters between a and B Operation in the 135 kHz Band Power-on Message Mode Selection of Built-in Electronic KeyerDouble Function Keys and Hold Time Selection Cross Tone Function Quick Memory FunctionPF Keys MIC CN Expansion of Voice Guide Function Optional VGS-1 Required Easy Updating of Firmware Projections on the Rear Panel A Sketch of the TS-590S Structural Features Cooling Structural Features Heat Sink Section LCD Amber and Green Main Control Knob Main Control Knob Expansive Application Software System ConfigurationsControlling TS-590S from a PC using the COM Connector Windows Related Software Controlling TS-590S from a PC using the USB Connector Connection Controlling TS-590S from a PC on a Remote Site Software Hardware Basic Specifications Inherited from ARCP-480 User Interfaces KNS Kenwood Network Command System Menu Function KNS Welcome Message Visual Scan Audio Equalizer Basic Specifications Inherited from ARHP-10 ARHP-590 Amateur Radio Host Program Freeware New ARUA-10 USB Audio Controller Freeware Disabling AF Gain Control from ARCP-590 Basic Functions SetupOperation Automatic Execution when Windows Starts Adjusting VolumeStarting and Stopping ARUA-10 New ARVP-10H Amateur Radio VoIP Program Freeware 12 Main Window of ARVP-10H Setup of ARVP-10H Host Station Making ARVP-10H host station Online or Offline Setup of ARVP-10R remote station Connecting and Disconnecting ARVP-10R Remote Station New Virtual COM Port Driver 16 Device Manager Optional Accessory PS-60 Regulated DC Power Supply Rectifier Circuit Comparing Rectification WaveformsPage Revision 1.00 May 15