Manuals / Lenovo / Computer Equipment / Server

Lenovo RD120 PCI riser-cardadapter connectors, Power-backplane-boardconnectors, Fan 10 connector

Models: RD120

1 118

Download 118 pages 33.27 Kb

Page 33

PCI riser-card adapter connectors

PCI riser-card adapter connectors

The following illustration shows the connectors 1 on the PCI riser card for user-installable PCI adapters.

Note: For clarity, in the following illustration the PCI riser-card assembly is inverted.

Power-backplane-board connectors

The following illustration shows the internal connectors on the power-backplane board.

1	Fan 10 connector
2	Hard disk drive power connector
3	Fan 7 connector
4	System board connector

Chapter 2. Installing optional devices 19

Image 33

Lenovo RD120 manual PCI riser-cardadapter connectors, Power-backplane-boardconnectors, Fan 10 connector, Fan 7 connector

Contents

ThinkServer RD120 Types 6444, 6445, 6446, and User GuidePage ThinkServer RD120 Types 6444, 6445, 6446, and User GuideFourth Edition April Copyright Lenovo 2008, Chapter 1. The ThinkServer RD120 server ContentsChapter 3. Configuring the server Safety Each caution and danger statement in this document is labeled with a number. This number is used to cross reference an English language caution or danger statement with translated versions of the caution or danger statement in the Safety Information document, which is provided on the ThinkServer Documentation DVD Statement DANGER Statement Statement Statement Statement Statement Lenovo 2008, 2009. Portions IBM Corp. Chapter 1. The ThinkServer RD120 serverNotices and statements in this document Related documentationvInstallation Guide vWarranty and Support InformationNotes Features and specificationsvBaseboard management controller What your server offersvThinkServer EasyStartup DVD vDiagnostics CDvEasyManage software vIntegrated network supportvRedundant cooling and power capabilities vEasy LED DiagnosticsvMemory mirroring vOnline-sparememoryvTCP/IP offload engine TOE support vSystems-managementcapabilitiesServer controls, LEDs, and power ThinkServer EasyStartupFront view Operator information panel Rear view 20 Power supply 10 USB 3 connectorServer power features Turning on the serverTurning off the server Attention: In a dc power environment, only trained service personnel other than Lenovo service technicians are authorized to connect or disconnect power to the dc power supply. See the documentation that comes with each dc power supply Page Server components Chapter 2. Installing optional devicesCover Riser-cardassembly Fan connectors System-board optional-deviceconnectorsVoltage regulator module connector connectorPower-backplane-boardconnectors PCI riser-cardadapter connectorsFan 10 connector Fan 7 connectorSystem-boardinternal cable connectors Ethernet connectors 1 and 2 and USB System-boardexternal connectorsSerial connector connectors 3 andSystem-boardswitches and jumpers Boot block recovery jumper J42Switch block SW2 Switch SwitchDefault value numberSystem-boardLEDs Riser-cardassembly LEDs PCI slot 1 error LEDPCI slot 2 error LED Diagnostics Diagnostics panelLight Path DescriptionThe power supply in bay 2 has failed DescriptionAction Description ActionRAID Installation guidelines System reliability guidelines Working inside the server with the power onRemoving the cover Handling static-sensitivedevicesRemoving the riser-cardassembly 1 Access holes 2 Release tabs Removing the microprocessor air baffle Installing the riser-cardassembly1 Access holes 2 Guide 3 Release tabs 4 GuideChapter 2. Installing optional devices Finger holesMicroprocessor air baffle Installing the microprocessor air baffle DIMM air baffle Removing the DIMM air baffleFinger hole Release ringRiser card assembly Installing the DIMM air baffleInstalling an adapter PCI riser card 1.Read the safety information that begins on page v and “Installation guidelines” on page 9.Connect any required cables to the adapter Raiser-cardassembly Removing an adapterExpansion slot cover Expansion slot cover6.Disconnect any cables from the adapter Replacing the RAID SAS controller Battery cable Battery mounting tabsBattery mounting clips Battery3.5-inchdrives Installing a hard disk drive2.5-inchdrives 1 Tray handle 2 Hard disk drive Removing a hard disk driveInstalling an optional tape drive 8.Connect the cables to the back of the tape drive 1 SATA tape cable connector 2 SATA tape cable 6.Remove the filler panel from the tape-drivebay SATA tape cable Installing a microprocessorPage Microprocessor-socketdust cover 5.Install the VRM in the VRM connector 10.Install a heat sink on the microprocessor 3 Heat-sink-releaselever 1 Retainer bracket 2 MicroprocessorInstalling a memory module DIMM connectorsPair DIMM Memory mirroring DIMM connectors Online-sparememoryGroup GroupDIMM connectors DIMM connectorsNumber of DIMMsRemoving a memory module Installing a hot-swappower supplyPower supply Installed power suppliesPower supplies 1 and Hot-swappower supplyChapter 2. Installing optional devices Power cord connectorsInstalling a fan Removing a hot-swappower supplyRemoving a fan Removing the fan-bracketassembly Fan bracket Chapter 2. Installing optional devicesLever LeverInstalling the fan-bracketassembly Replacing the CD-RW/DVDdrive Completing the installation Installing the cover Connecting the cablesFront view Rear view Updating the server configurationIf you have installed or removed a hard disk drive, see “Using the RAID Configuration Utility program” on page 87 for information about reconfiguring the disk arrays Page Chapter 3. Configuring the server Using the Configuration/Setup Utility programvThinkServer EasyStartup DVD Configuration/Setup Utility menu choices Starting the Configuration/Setup Utility programvSystem Summary vSystem Information–Power-onPassword –Administrator PasswordvAdvanced Setup –Memory Settings–CPU Options BMC Build Level Power-onpassword PasswordsResetting passwords Administrator passwordTo clear CMOS and reset the passwords, complete the following steps Starting the RAID Configuration Utility program Using the RAID Configuration Utility programConfiguring the controller RAID Configuration Utility menu choicesViewing the configuration Using the baseboard management controllerConfiguring the Gigabit Ethernet controllers Page Lenovo United States, Inc Appendix. Notices1009 Think Place - Building One Morrisville, NC U.S.A Attention: Lenovo Director of LicensingImportant notes TrademarksAppendix. Notices Recycling statements for Japan For the European Union Battery return programElectronic emission notices German Ordinance for Work gloss statementFederal Communications Commission FCC statement For CaliforniaAustralia and New Zealand Class A statement Taiwanese Class A warning statementNotice to Customers Chinese Class A warning statement Lenovo product service information for TaiwanIndex A Page Page voltage regulator module, installing VRM video connector continued rearLenovo ThinkServer RD120 products 1 weight 3, See voltage regulator modulePage 1P P/N: 46U0861 Part Number: 46U0861 Printed in USA