Manuals / Lenovo / Computer Equipment / Server

Lenovo RD120 manual System-boardinternal cable connectors

Models: RD120

1 118

Download 118 pages 33.27 Kb

Page 34

System-board internal cable connectors

System-board internal cable connectors

The following illustration shows the internal connectors on the system board.

1	Hard disk drive backplane signal	7	CD/DVD signal (J37)
	(J92)
2	Power backplane (J72)	8	CD/DVD power (J12)
3	Tape drive power (J100)	9	Operator information panel (J50)
4	Front USB (J80)	10	SATA tape drive signal (J102)
5	Front video (J51)	11	Intelligent Platform Management Bus
			(IPMB) connector
6	Internal USB (J82)

20ThinkServer RD120 Types 6444, 6445, 6446, and 6447: User Guide

Image 34

Lenovo RD120 manual System-boardinternal cable connectors

Contents

User Guide ThinkServer RD120 Types 6444, 6445, 6446, andPage User Guide ThinkServer RD120 Types 6444, 6445, 6446, andFourth Edition April Copyright Lenovo 2008, Contents Chapter 1. The ThinkServer RD120 serverChapter 3. Configuring the server Safety Each caution and danger statement in this document is labeled with a number. This number is used to cross reference an English language caution or danger statement with translated versions of the caution or danger statement in the Safety Information document, which is provided on the ThinkServer Documentation DVD Statement DANGER Statement Statement Statement Statement Statement Chapter 1. The ThinkServer RD120 server Lenovo 2008, 2009. Portions IBM Corp.vInstallation Guide Related documentationNotices and statements in this document vWarranty and Support InformationFeatures and specifications NotesWhat your server offers vBaseboard management controllervEasyManage software vDiagnostics CDvThinkServer EasyStartup DVD vIntegrated network supportvMemory mirroring vEasy LED DiagnosticsvRedundant cooling and power capabilities vOnline-sparememoryvSystems-managementcapabilities vTCP/IP offload engine TOE supportThinkServer EasyStartup Server controls, LEDs, and powerFront view Operator information panel Rear view 10 USB 3 connector 20 Power supplyTurning on the server Server power featuresTurning off the server Attention: In a dc power environment, only trained service personnel other than Lenovo service technicians are authorized to connect or disconnect power to the dc power supply. See the documentation that comes with each dc power supply Page Chapter 2. Installing optional devices Server componentsCover Riser-cardassembly Voltage regulator module connector System-board optional-deviceconnectorsFan connectors connectorFan 10 connector PCI riser-cardadapter connectorsPower-backplane-boardconnectors Fan 7 connectorSystem-boardinternal cable connectors Serial connector System-boardexternal connectorsEthernet connectors 1 and 2 and USB connectors 3 andBoot block recovery jumper J42 System-boardswitches and jumpersSwitch block SW2 Default value SwitchSwitch numberSystem-boardLEDs PCI slot 1 error LED Riser-cardassembly LEDsPCI slot 2 error LED Light Path Diagnostics panelDiagnostics DescriptionDescription The power supply in bay 2 has failedAction Action DescriptionRAID Installation guidelines Working inside the server with the power on System reliability guidelinesHandling static-sensitivedevices Removing the coverRemoving the riser-cardassembly 1 Access holes 2 Release tabs 1 Access holes 2 Guide 3 Release tabs Installing the riser-cardassemblyRemoving the microprocessor air baffle 4 GuideFinger holes Chapter 2. Installing optional devicesMicroprocessor air baffle Installing the microprocessor air baffle Finger hole Removing the DIMM air baffleDIMM air baffle Release ringInstalling the DIMM air baffle Riser card assemblyInstalling an adapter PCI riser card 1.Read the safety information that begins on page v and “Installation guidelines” on page 9.Connect any required cables to the adapter Expansion slot cover Removing an adapterRaiser-cardassembly Expansion slot cover6.Disconnect any cables from the adapter Replacing the RAID SAS controller Battery mounting clips Battery mounting tabsBattery cable BatteryInstalling a hard disk drive 3.5-inchdrives2.5-inchdrives Removing a hard disk drive 1 Tray handle 2 Hard disk driveInstalling an optional tape drive 8.Connect the cables to the back of the tape drive 1 SATA tape cable connector 2 SATA tape cable 6.Remove the filler panel from the tape-drivebay Installing a microprocessor SATA tape cablePage Microprocessor-socketdust cover 5.Install the VRM in the VRM connector 10.Install a heat sink on the microprocessor 1 Retainer bracket 2 Microprocessor 3 Heat-sink-releaseleverDIMM connectors Installing a memory modulePair DIMM Memory mirroring Group Online-sparememoryDIMM connectors GroupNumber of DIMM connectorsDIMM connectors DIMMsInstalling a hot-swappower supply Removing a memory modulePower supplies 1 and Installed power suppliesPower supply Hot-swappower supplyPower cord connectors Chapter 2. Installing optional devicesRemoving a hot-swappower supply Installing a fanRemoving a fan Removing the fan-bracketassembly Lever Chapter 2. Installing optional devicesFan bracket LeverInstalling the fan-bracketassembly Replacing the CD-RW/DVDdrive Completing the installation Connecting the cables Installing the coverFront view Updating the server configuration Rear viewIf you have installed or removed a hard disk drive, see “Using the RAID Configuration Utility program” on page 87 for information about reconfiguring the disk arrays Page Using the Configuration/Setup Utility program Chapter 3. Configuring the servervThinkServer EasyStartup DVD vSystem Summary Starting the Configuration/Setup Utility programConfiguration/Setup Utility menu choices vSystem InformationvAdvanced Setup –Administrator Password–Power-onPassword –Memory Settings–CPU Options BMC Build Level Passwords Power-onpasswordAdministrator password Resetting passwordsTo clear CMOS and reset the passwords, complete the following steps Using the RAID Configuration Utility program Starting the RAID Configuration Utility programViewing the configuration RAID Configuration Utility menu choicesConfiguring the controller Using the baseboard management controllerConfiguring the Gigabit Ethernet controllers Page 1009 Think Place - Building One Morrisville, NC Appendix. NoticesLenovo United States, Inc U.S.A Attention: Lenovo Director of LicensingTrademarks Important notesAppendix. Notices Recycling statements for Japan Battery return program For the European UnionFederal Communications Commission FCC statement German Ordinance for Work gloss statementElectronic emission notices For CaliforniaTaiwanese Class A warning statement Australia and New Zealand Class A statementNotice to Customers Lenovo product service information for Taiwan Chinese Class A warning statementIndex A Page Page Lenovo ThinkServer RD120 products 1 weight 3, video connector continued rearvoltage regulator module, installing VRM See voltage regulator modulePage Part Number: 46U0861 Printed in USA 1P P/N: 46U0861