Manuals / Lenovo / Computer Equipment / Server

Lenovo RD120 manual Removing a hard disk drive, 1 Tray handle 2 Hard disk drive

Models: RD120

1 118

Download 118 pages 33.27 Kb

Page 63

Removing a hard disk drive

Removing a hard disk drive

3.5-inch drives

1 Tray handle

2 Hard disk drive

Chapter 2. Installing optional devices 49

Image 63

Lenovo RD120 manual Removing a hard disk drive, 1 Tray handle 2 Hard disk drive

Contents

ThinkServer RD120 Types 6444, 6445, 6446, and User GuidePage ThinkServer RD120 Types 6444, 6445, 6446, and User GuideFourth Edition April Copyright Lenovo 2008, Chapter 1. The ThinkServer RD120 server ContentsChapter 3. Configuring the server Safety Each caution and danger statement in this document is labeled with a number. This number is used to cross reference an English language caution or danger statement with translated versions of the caution or danger statement in the Safety Information document, which is provided on the ThinkServer Documentation DVD Statement DANGER Statement Statement Statement Statement Statement Lenovo 2008, 2009. Portions IBM Corp. Chapter 1. The ThinkServer RD120 servervWarranty and Support Information Related documentationNotices and statements in this document vInstallation GuideNotes Features and specificationsvBaseboard management controller What your server offersvIntegrated network support vDiagnostics CDvThinkServer EasyStartup DVD vEasyManage softwarevOnline-sparememory vEasy LED DiagnosticsvRedundant cooling and power capabilities vMemory mirroringvTCP/IP offload engine TOE support vSystems-managementcapabilitiesServer controls, LEDs, and power ThinkServer EasyStartupFront view Operator information panel Rear view 20 Power supply 10 USB 3 connectorServer power features Turning on the serverTurning off the server Attention: In a dc power environment, only trained service personnel other than Lenovo service technicians are authorized to connect or disconnect power to the dc power supply. See the documentation that comes with each dc power supply Page Server components Chapter 2. Installing optional devicesCover Riser-cardassembly connector System-board optional-deviceconnectorsFan connectors Voltage regulator module connectorFan 7 connector PCI riser-cardadapter connectorsPower-backplane-boardconnectors Fan 10 connectorSystem-boardinternal cable connectors connectors 3 and System-boardexternal connectorsEthernet connectors 1 and 2 and USB Serial connectorSystem-boardswitches and jumpers Boot block recovery jumper J42Switch block SW2 number SwitchSwitch Default valueSystem-boardLEDs Riser-cardassembly LEDs PCI slot 1 error LEDPCI slot 2 error LED Description Diagnostics panelDiagnostics Light PathThe power supply in bay 2 has failed DescriptionAction Description ActionRAID Installation guidelines System reliability guidelines Working inside the server with the power onRemoving the cover Handling static-sensitivedevicesRemoving the riser-cardassembly 1 Access holes 2 Release tabs 4 Guide Installing the riser-cardassemblyRemoving the microprocessor air baffle 1 Access holes 2 Guide 3 Release tabsChapter 2. Installing optional devices Finger holesMicroprocessor air baffle Installing the microprocessor air baffle Release ring Removing the DIMM air baffleDIMM air baffle Finger holeRiser card assembly Installing the DIMM air baffleInstalling an adapter PCI riser card 1.Read the safety information that begins on page v and “Installation guidelines” on page 9.Connect any required cables to the adapter Expansion slot cover Removing an adapterRaiser-cardassembly Expansion slot cover6.Disconnect any cables from the adapter Replacing the RAID SAS controller Battery Battery mounting tabsBattery cable Battery mounting clips3.5-inchdrives Installing a hard disk drive2.5-inchdrives 1 Tray handle 2 Hard disk drive Removing a hard disk driveInstalling an optional tape drive 8.Connect the cables to the back of the tape drive 1 SATA tape cable connector 2 SATA tape cable 6.Remove the filler panel from the tape-drivebay SATA tape cable Installing a microprocessorPage Microprocessor-socketdust cover 5.Install the VRM in the VRM connector 10.Install a heat sink on the microprocessor 3 Heat-sink-releaselever 1 Retainer bracket 2 MicroprocessorInstalling a memory module DIMM connectorsPair DIMM Memory mirroring Group Online-sparememoryDIMM connectors GroupDIMMs DIMM connectorsDIMM connectors Number ofRemoving a memory module Installing a hot-swappower supplyHot-swappower supply Installed power suppliesPower supply Power supplies 1 andChapter 2. Installing optional devices Power cord connectorsInstalling a fan Removing a hot-swappower supplyRemoving a fan Removing the fan-bracketassembly Lever Chapter 2. Installing optional devicesFan bracket LeverInstalling the fan-bracketassembly Replacing the CD-RW/DVDdrive Completing the installation Installing the cover Connecting the cablesFront view Rear view Updating the server configurationIf you have installed or removed a hard disk drive, see “Using the RAID Configuration Utility program” on page 87 for information about reconfiguring the disk arrays Page Chapter 3. Configuring the server Using the Configuration/Setup Utility programvThinkServer EasyStartup DVD vSystem Information Starting the Configuration/Setup Utility programConfiguration/Setup Utility menu choices vSystem Summary–Memory Settings –Administrator Password–Power-onPassword vAdvanced Setup–CPU Options BMC Build Level Power-onpassword PasswordsResetting passwords Administrator passwordTo clear CMOS and reset the passwords, complete the following steps Starting the RAID Configuration Utility program Using the RAID Configuration Utility programUsing the baseboard management controller RAID Configuration Utility menu choicesConfiguring the controller Viewing the configurationConfiguring the Gigabit Ethernet controllers Page U.S.A Attention: Lenovo Director of Licensing Appendix. NoticesLenovo United States, Inc 1009 Think Place - Building One Morrisville, NCImportant notes TrademarksAppendix. Notices Recycling statements for Japan For the European Union Battery return programFor California German Ordinance for Work gloss statementElectronic emission notices Federal Communications Commission FCC statementAustralia and New Zealand Class A statement Taiwanese Class A warning statementNotice to Customers Chinese Class A warning statement Lenovo product service information for TaiwanIndex A Page Page See voltage regulator module video connector continued rearvoltage regulator module, installing VRM Lenovo ThinkServer RD120 products 1 weight 3,Page 1P P/N: 46U0861 Part Number: 46U0861 Printed in USA