Manuals / Lenovo / Computer Equipment / Server

Lenovo RD120 manual Statement

Models: RD120

1 118

Download 118 pages 33.27 Kb

Page 13

Manual background

Statement 8:

CAUTION:

Never remove the cover on a power supply or any part that has the following label attached.

Hazardous voltage, current, and energy levels are present inside any component that has this label attached. There are no serviceable parts inside these components. If you suspect a problem with one of these parts, contact a service technician.

Statement 12:

CAUTION:

The following label indicates a hot surface nearby.

Statement 13:

DANGER

Overloading a branch circuit is potentially a fire hazard and a shock hazard under certain conditions. To avoid these hazards, ensure that your system electrical requirements do not exceed branch circuit protection requirements. Refer to the information that is provided with your device for electrical specifications.

Safety xi

Image 13

Lenovo RD120 manual Statement

Contents

ThinkServer RD120 Types 6444, 6445, 6446, and User GuidePage ThinkServer RD120 Types 6444, 6445, 6446, and User GuideFourth Edition April Copyright Lenovo 2008, Chapter 1. The ThinkServer RD120 server ContentsChapter 3. Configuring the server Safety Each caution and danger statement in this document is labeled with a number. This number is used to cross reference an English language caution or danger statement with translated versions of the caution or danger statement in the Safety Information document, which is provided on the ThinkServer Documentation DVD Statement DANGER Statement Statement Statement Statement Statement Lenovo 2008, 2009. Portions IBM Corp. Chapter 1. The ThinkServer RD120 serverNotices and statements in this document Related documentationvInstallation Guide vWarranty and Support InformationNotes Features and specificationsvBaseboard management controller What your server offersvThinkServer EasyStartup DVD vDiagnostics CDvEasyManage software vIntegrated network supportvRedundant cooling and power capabilities vEasy LED DiagnosticsvMemory mirroring vOnline-sparememoryvTCP/IP offload engine TOE support vSystems-managementcapabilitiesThinkServer EasyStartup Server controls, LEDs, and powerFront view Operator information panel Rear view 20 Power supply 10 USB 3 connectorTurning on the server Server power featuresTurning off the server Attention: In a dc power environment, only trained service personnel other than Lenovo service technicians are authorized to connect or disconnect power to the dc power supply. See the documentation that comes with each dc power supply Page Server components Chapter 2. Installing optional devicesCover Riser-cardassembly Fan connectors System-board optional-deviceconnectorsVoltage regulator module connector connectorPower-backplane-boardconnectors PCI riser-cardadapter connectorsFan 10 connector Fan 7 connectorSystem-boardinternal cable connectors Ethernet connectors 1 and 2 and USB System-boardexternal connectorsSerial connector connectors 3 andBoot block recovery jumper J42 System-boardswitches and jumpersSwitch block SW2 Switch SwitchDefault value numberSystem-boardLEDs PCI slot 1 error LED Riser-cardassembly LEDsPCI slot 2 error LED Diagnostics Diagnostics panelLight Path DescriptionDescription The power supply in bay 2 has failedAction Action DescriptionRAID Installation guidelines System reliability guidelines Working inside the server with the power onRemoving the cover Handling static-sensitivedevicesRemoving the riser-cardassembly 1 Access holes 2 Release tabs Removing the microprocessor air baffle Installing the riser-cardassembly1 Access holes 2 Guide 3 Release tabs 4 GuideFinger holes Chapter 2. Installing optional devicesMicroprocessor air baffle Installing the microprocessor air baffle DIMM air baffle Removing the DIMM air baffleFinger hole Release ringRiser card assembly Installing the DIMM air baffleInstalling an adapter PCI riser card 1.Read the safety information that begins on page v and “Installation guidelines” on page 9.Connect any required cables to the adapter Raiser-cardassembly Removing an adapterExpansion slot cover Expansion slot cover6.Disconnect any cables from the adapter Replacing the RAID SAS controller Battery cable Battery mounting tabsBattery mounting clips Battery3.5-inchdrives Installing a hard disk drive2.5-inchdrives 1 Tray handle 2 Hard disk drive Removing a hard disk driveInstalling an optional tape drive 8.Connect the cables to the back of the tape drive 1 SATA tape cable connector 2 SATA tape cable 6.Remove the filler panel from the tape-drivebay SATA tape cable Installing a microprocessorPage Microprocessor-socketdust cover 5.Install the VRM in the VRM connector 10.Install a heat sink on the microprocessor 3 Heat-sink-releaselever 1 Retainer bracket 2 MicroprocessorDIMM connectors Installing a memory modulePair DIMM Memory mirroring DIMM connectors Online-sparememoryGroup GroupDIMM connectors DIMM connectorsNumber of DIMMsRemoving a memory module Installing a hot-swappower supplyPower supply Installed power suppliesPower supplies 1 and Hot-swappower supplyChapter 2. Installing optional devices Power cord connectorsInstalling a fan Removing a hot-swappower supplyRemoving a fan Removing the fan-bracketassembly Fan bracket Chapter 2. Installing optional devicesLever LeverInstalling the fan-bracketassembly Replacing the CD-RW/DVDdrive Completing the installation Connecting the cables Installing the coverFront view Rear view Updating the server configurationIf you have installed or removed a hard disk drive, see “Using the RAID Configuration Utility program” on page 87 for information about reconfiguring the disk arrays Page Using the Configuration/Setup Utility program Chapter 3. Configuring the servervThinkServer EasyStartup DVD Configuration/Setup Utility menu choices Starting the Configuration/Setup Utility programvSystem Summary vSystem Information–Power-onPassword –Administrator PasswordvAdvanced Setup –Memory Settings–CPU Options BMC Build Level Power-onpassword PasswordsResetting passwords Administrator passwordTo clear CMOS and reset the passwords, complete the following steps Starting the RAID Configuration Utility program Using the RAID Configuration Utility programConfiguring the controller RAID Configuration Utility menu choicesViewing the configuration Using the baseboard management controllerConfiguring the Gigabit Ethernet controllers Page Lenovo United States, Inc Appendix. Notices1009 Think Place - Building One Morrisville, NC U.S.A Attention: Lenovo Director of LicensingImportant notes TrademarksAppendix. Notices Recycling statements for Japan For the European Union Battery return programElectronic emission notices German Ordinance for Work gloss statementFederal Communications Commission FCC statement For CaliforniaTaiwanese Class A warning statement Australia and New Zealand Class A statementNotice to Customers Chinese Class A warning statement Lenovo product service information for TaiwanIndex A Page Page voltage regulator module, installing VRM video connector continued rearLenovo ThinkServer RD120 products 1 weight 3, See voltage regulator modulePage 1P P/N: 46U0861 Part Number: 46U0861 Printed in USA