Introduction | HP 1GSa/s Digitizing Oscilloscope 16532A guide

1-1. Introduction

The service policy for this instrument is replace- ment of defective assemblies. This service guidel contains information for finding a defective assembly by testing and servicing the HP 16532A 1 GSa/s Oscilloscope Module. Also included in the guide are installation procedures and a list of recommended test equipment. This guide is divided into six sections as follows:

I - General Information

II - Installation

III- Performance Tests

IV - Calibration

V- Replaceable Parts

VI - Service

The General Information Section includes safety requirements, a product description, and a list of accessories supplied and of accessories available. Also included are tables listing specifications and operating characteristics, and a list of recommended test equipment.

HP 16532A - General Information

SECTION I General Information

To complete the service documentation for your HP 16500 Logic Analysis System, place this service manual in the 3-ring binder with your other logic analysis system Service Guides.

1-2. Module Covered by This Manual

The information covered in this manual is for the HP 16532A 1 GSa/s Oscilloscope Module.

1-3. Safety Requirements

Specific warnings, cautions, and instructions are placed wherever applicable throughout the manual. These must be observed during all phases of operation, service, and repair of the module. Failure to comply with them violates safety standards of design, manufacture, and intended use of this module.

Hewlett-Packard assumes no liability for the failure of the customer to comply with these safety requirements.

1-1

Image 9

HP 1GSa/s Digitizing Oscilloscope 16532A manual Introduction, Module Covered by This Manual, Safety Requirements

Contents

HP 16532A Safety Symbols Safety Considerations Contents Service CalibrationSection Replaceable Parts List of Tables Page Table of Contents Page Safety Requirements IntroductionModule Covered by This Manual Accessories Available Accessories SuppliedSpecifications Operating Characteristics Rise Time2 1.4 ns HP 16532A SpecificationsWaveform Record Length 8000 points Vertical dc Gain Accuracy4 ± 1.5% of full scale HP 16532A Operating Characteristics Vertical at BNCTimebase Digitizer TriggeringTrigger Level Range Trigger Modes Display Modes Waveform Display Measurement Aids Operating Environment Setup Aids Equipment Critical Specifications Recommended Model USE Page Table of Contents Page Initial Inspection Safety Requirements Power RequirementsModule Installation Preparation for Use Procedure Installation Considerations Endplate Overlap Bottom Sequence Operating Environment Tagging for ServiceStorage Packaging Table of Contents Page Performance Test Procedures Test RecordPerformance Test Interval DC CAL Output Test AC CAL Output Test Specification Equipment Required Critical Specification Model/Part NumberInput Resistance Page Voltage Measurement Accuracy Voltage Measurement Accuracy Test Div Offset Supply Upper Limit Lower Limit Offset Accuracy Procedure Zero-Input Offset Div Offset Supply Min Max DC Input Offset Bandwidth V1MHz Time Measurement Accuracy Menu Selection Setting Trigger Sensitivity RUN Repetitive Performance Test Record Paragraph No Test Results Yes No Page Table of Contents Page Calibration Protection Switch Calibration IntervalMaintaining System Integrity Calibration Instrument Warmup Location of the PROTECT/UNPROTECT Switch Setting the PROTECT/UNPROTECT Switch to Unprotect Equipment Required for Calibration Loading the Default Calibration Factors Calibrate Delay of the Self Cal menu as follows Self Cal Menu CalibrationsCalibrate Vert Cal of the Self Cal menu as follows Calibrate the Logic Trigger of the Self Cal menu as follows Calibrate the Time Null of the Self Cal menu as follows Ext Trig Null Calibration Connections Calibrate the Ext Trig Null of the Self Cal menu as follows Sealing the Mainframe Setting the PROTECT/UNPROTECT Switch to Protect Table of Contents Page Abbreviations Replaceable Parts ListOrdering Information Exchange Assemblies Direct Mail Order System Reference Designator and Abbreviations Parts Identification HP Part Qty Number Reference DesignatorDescription Mfr Code Mfr Part NumberPage Table of Contents Page Module Block Diagram and The- ory of Operation Introduction Safety RequirementsMain Assembly Theory of Operation Attenuator Theory of Operation HP 16532A Oscilloscope Block Diagram Page Self-Tests Self-Test Access Procedure Load Test System Screen Touch the Functional Tests field Functional Tests Screen A/D Test Run Screen Exit Test System Screen Data Memory Test Self-Test DescriptionsTimebase Test Test Troubleshooting Aids Troubleshooting Verifying the System Clock Page Troubleshooting E E T Troubleshooting Sheet1 6 5 3 2 a Troubleshooting E E T Troubleshooting E E T Troubleshooting E E T Troubleshooting E E T Oscilloscope Module Removal Procedure Oscilloscope Module Removal and Replacement 12. Endplate Overlap Bottom Sequence Oscilloscope Module Replacement Procedure Trigger Cable Removal Procedure Trigger Cable Removal and Replacement Attenuator Removal and Replacement Trigger Cable Replacement ProcedureAttenuator Removal Procedure Attenuator Replacement Procedure Warranty CertificationAssistance