Procedure | HP 1GSa/s Digitizing Oscilloscope 16532A specification

HP 16532A - Installation

Module Installation (cont.)

The effects of ELECTROSTATIC DISCHARGE can damage electronic compo- nents. Use grounded wrist straps and mats when you are performing any kind of service to this module.

Installation Considerations

∙The HP 16532A Oscilloscope Modules can be installed in any available card slot.

∙For multiple modules connected as one unit, the master card must be placed in the slot above the expander cards. The master card and expander cards must be in adjoining slots.

∙Cards or filler panels below the empty slots intended for module installation do not have to be re- moved to install a module above them.

Procedure:

1.Turn instrument power switch off, unplug power cord and disconnect any input connections.

2.Starting from the top, loosen the thumb screws on the filler panels and cards.

3.Starting from the top, begin pulling out the cards and filler panels halfway. See figure 2-1.

Figure 2-1. Endplate Overlap - Top Sequence

2-2

Image 22

HP 1GSa/s Digitizing Oscilloscope 16532A manual Installation Considerations, Procedure

Contents

HP 16532A Safety Considerations Safety Symbols Contents Calibration ServiceSection Replaceable Parts List of Tables Page Table of Contents Page Introduction Safety RequirementsModule Covered by This Manual Specifications Accessories SuppliedAccessories Available Operating Characteristics Waveform Record Length 8000 points HP 16532A SpecificationsRise Time2 1.4 ns Vertical dc Gain Accuracy4 ± 1.5% of full scale Vertical at BNC HP 16532A Operating CharacteristicsTimebase Trigger Level Range TriggeringDigitizer Trigger Modes Waveform Display Display Modes Measurement Aids Setup Aids Operating Environment Equipment Critical Specifications Recommended Model USE Page Table of Contents Page Module Installation Power RequirementsInitial Inspection Safety Requirements Preparation for Use Installation Considerations Procedure Endplate Overlap Bottom Sequence Storage Tagging for ServiceOperating Environment Packaging Table of Contents Page Test Record Performance Test ProceduresPerformance Test Interval DC CAL Output Test AC CAL Output Test Equipment Required Critical Specification Model/Part Number SpecificationInput Resistance Page Voltage Measurement Accuracy Voltage Measurement Accuracy Test Div Offset Supply Upper Limit Lower Limit Procedure Zero-Input Offset Offset Accuracy DC Input Offset Div Offset Supply Min Max Bandwidth V1MHz Time Measurement Accuracy Menu Selection Setting Trigger Sensitivity RUN Repetitive Performance Test Record Paragraph No Test Results Yes No Page Table of Contents Page Calibration Interval Calibration Protection SwitchMaintaining System Integrity Instrument Warmup Calibration Setting the PROTECT/UNPROTECT Switch to Unprotect Location of the PROTECT/UNPROTECT Switch Loading the Default Calibration Factors Equipment Required for Calibration Self Cal Menu Calibrations Calibrate Delay of the Self Cal menu as followsCalibrate Vert Cal of the Self Cal menu as follows Calibrate the Time Null of the Self Cal menu as follows Calibrate the Logic Trigger of the Self Cal menu as follows Calibrate the Ext Trig Null of the Self Cal menu as follows Ext Trig Null Calibration Connections Setting the PROTECT/UNPROTECT Switch to Protect Sealing the Mainframe Table of Contents Page Ordering Information Replaceable Parts ListAbbreviations Exchange Assemblies Direct Mail Order System Reference Designator and Abbreviations Parts Identification Description Reference DesignatorHP Part Qty Number Mfr Code Mfr Part NumberPage Table of Contents Page Main Assembly Theory of Operation Introduction Safety RequirementsModule Block Diagram and The- ory of Operation Attenuator Theory of Operation HP 16532A Oscilloscope Block Diagram Page Self-Test Access Procedure Self-Tests Load Test System Screen Functional Tests Screen Touch the Functional Tests field A/D Test Run Screen Exit Test System Screen Timebase Test Self-Test DescriptionsData Memory Test Test Troubleshooting Troubleshooting Aids Verifying the System Clock Page Troubleshooting Sheet Troubleshooting E E T1 6 5 3 2 a Troubleshooting E E T Troubleshooting E E T Troubleshooting E E T Troubleshooting E E T Oscilloscope Module Removal and Replacement Oscilloscope Module Removal Procedure Oscilloscope Module Replacement Procedure 12. Endplate Overlap Bottom Sequence Trigger Cable Removal and Replacement Trigger Cable Removal Procedure Trigger Cable Replacement Procedure Attenuator Removal and ReplacementAttenuator Removal Procedure Attenuator Replacement Procedure Certification WarrantyAssistance