Direct Mail Order System | HP 1GSa/s Digitizing Oscilloscope 16532A

HP 16532A - Replaceable Parts

Exchange assemblies are listed in a separate section in the replaceable parts table. They have a part number in the form XXXXX-695XX (where the new parts would be XXXXX-665XX). Before ordering an "exchange assembly," check with your local parts or repair organization for procedures.

5-6. Direct Mail Order System

Within the USA, Hewlett-Packard can supply parts through direct mail order. The advantages are as follows:

∙Direct ordering and shipment from Hewlett-Packard Parts Center in Mountain View, California.

∙No maximum or minimum on any mail order (there is a minimum order for parts ordered through local Hewlett-Packard offices when orders require billing and invoicing).

∙Prepaid transportation (there is a small handling charge for each order).

∙No invoices - to provide these advantages, check or money order must accompany each order.

Mail order forms and specific ordering information are available through your local Hewlett-Packard offices.

5-2

Image 60

HP 1GSa/s Digitizing Oscilloscope 16532A manual Direct Mail Order System

Contents

HP 16532A Safety Considerations Safety Symbols Contents Service CalibrationSection Replaceable Parts List of Tables Page Table of Contents Page Safety Requirements IntroductionModule Covered by This Manual Accessories Supplied Accessories AvailableSpecifications Operating Characteristics HP 16532A Specifications Rise Time2 1.4 nsWaveform Record Length 8000 points Vertical dc Gain Accuracy4 ± 1.5% of full scale HP 16532A Operating Characteristics Vertical at BNCTimebase Triggering DigitizerTrigger Level Range Trigger Modes Waveform Display Display Modes Measurement Aids Setup Aids Operating Environment Equipment Critical Specifications Recommended Model USE Page Table of Contents Page Power Requirements Initial Inspection Safety RequirementsModule Installation Preparation for Use Installation Considerations Procedure Endplate Overlap Bottom Sequence Tagging for Service Operating EnvironmentStorage Packaging Table of Contents Page Performance Test Procedures Test RecordPerformance Test Interval DC CAL Output Test AC CAL Output Test Specification Equipment Required Critical Specification Model/Part NumberInput Resistance Page Voltage Measurement Accuracy Voltage Measurement Accuracy Test Div Offset Supply Upper Limit Lower Limit Procedure Zero-Input Offset Offset Accuracy DC Input Offset Div Offset Supply Min Max Bandwidth V1MHz Time Measurement Accuracy Menu Selection Setting Trigger Sensitivity RUN Repetitive Performance Test Record Paragraph No Test Results Yes No Page Table of Contents Page Calibration Protection Switch Calibration IntervalMaintaining System Integrity Instrument Warmup Calibration Setting the PROTECT/UNPROTECT Switch to Unprotect Location of the PROTECT/UNPROTECT Switch Loading the Default Calibration Factors Equipment Required for Calibration Calibrate Delay of the Self Cal menu as follows Self Cal Menu CalibrationsCalibrate Vert Cal of the Self Cal menu as follows Calibrate the Time Null of the Self Cal menu as follows Calibrate the Logic Trigger of the Self Cal menu as follows Calibrate the Ext Trig Null of the Self Cal menu as follows Ext Trig Null Calibration Connections Setting the PROTECT/UNPROTECT Switch to Protect Sealing the Mainframe Table of Contents Page Replaceable Parts List AbbreviationsOrdering Information Exchange Assemblies Direct Mail Order System Reference Designator and Abbreviations Parts Identification Reference Designator HP Part Qty NumberDescription Mfr Code Mfr Part NumberPage Table of Contents Page Introduction Safety Requirements Module Block Diagram and The- ory of OperationMain Assembly Theory of Operation Attenuator Theory of Operation HP 16532A Oscilloscope Block Diagram Page Self-Test Access Procedure Self-Tests Load Test System Screen Functional Tests Screen Touch the Functional Tests field A/D Test Run Screen Exit Test System Screen Self-Test Descriptions Data Memory TestTimebase Test Test Troubleshooting Troubleshooting Aids Verifying the System Clock Page Troubleshooting E E T Troubleshooting Sheet1 6 5 3 2 a Troubleshooting E E T Troubleshooting E E T Troubleshooting E E T Troubleshooting E E T Oscilloscope Module Removal and Replacement Oscilloscope Module Removal Procedure Oscilloscope Module Replacement Procedure 12. Endplate Overlap Bottom Sequence Trigger Cable Removal and Replacement Trigger Cable Removal Procedure Attenuator Removal and Replacement Trigger Cable Replacement ProcedureAttenuator Removal Procedure Attenuator Replacement Procedure Warranty CertificationAssistance