Desktop Installation, Attaching Rubber Feet | LevelOne GSW-2491TXM

LevelOne GSW-2491TXM as shown in Figure 2-3. The Switch will work with AC in the range 100-240V AC, 50-60Hz.

Figure 2-3. The Rear Panel of the LevelOne GSW-2491TXM

Desktop Installation

Set the Switch on a sufficiently large flat space with a power outlet nearby. The surface where you put your Switch should be clean, smooth, level and sturdy. Make sure there is enough clearance around the Switch to allow attachment of cables, power cord and allow air circulation.

Attaching Rubber Feet

A.Make sure mounting surface on the bottom of the Switch is grease and dust free.

B.Remove adhesive backing from your Rubber Feet.

C.Apply the Rubber Feet to each corner on the bottom of the Switch. These footpads can prevent the Switch from shock/vibration.

Figure 2-4. Attaching Rubber Feet to each corner on the bottom of the Switch

8

Image 14

LevelOne GSW-2491TXM user manual Desktop Installation, Attaching Rubber Feet

Contents

GSW-2491TXM Page Contents STP Snmp Lacp IGMP/GVRP 101 Page Introduction Software Upgrade FeaturesSoftware Features Management Spanning Tree Class of ServicePort Trunk QOS Policy Package Contents Ethernet Switching Technology Physical Dimension Front Panel LED Indicators Rear Panel Desktop Installation Attaching Rubber Feet Rack-mounted Installation Attach mounting brackets with screws Power On Mount the switch in an EIA standard 19-inch Rack Network Application Small Workgroup Segment Bridge Small Workgroup Application Stacking Workgroup Connecting to the Switch Stackable switch Master Login in the Console Interface Console Management Main Menu Main MenuConsole Menu Line Control Key description Status and Counters Port Status Port Counters System Information Switch Static Configuration Administration Configuration IP Configuration Device Information User Name Configuration Port Configuration Password Configuration Trunk Configuration Port Mirroring Configuration Port Mirroring interface — Vlan ID Port VID 1~255 Type the Pvid Vlan ConfigurationVlan Configure Create Vlan Group „ Create Port-Based Vlan „ Create 802.1Q Vlan Edit / Delete Vlan Group Group Sorted Mode Priority Configuration MAC Address Configuration Static MAC Address „ Add the Static MAC Address „ Edit static MAC address „ Add the Filtering MAC Address „ Delete static MAC addressFiltering MAC Address „ Delete Filtering MAC address Misc Configuration„ Edit Filtering MAC address „ IFG compensation Disable or Enable Misc Configuration interface Protocol Related Configuration STP Forward Delay Time forward delay time STP SetupSystem Configuration Per Port Setting Snmp Snmp System Options Community Strings „ Add Community Strings „ Edit Community Name „ Delete Community Name Trap Managers „ Add the trap manager Lacp „ Delete Trap Manager Select Delete Working Ports Setting Lacp State Activity IGMP/GVRP Group Status 802.1x Setup 802.1x 802.1x Setup interface Per Port Configuration Misc Configuration System Reset Configuration Factory Default Update Firmware System RebootTftp Configuration Tftp Restore Configuration Tftp Backup Configuration Modem Upgrade Page About Web-based Management Preparing for Web Management System Login Online Help Port status Port Statistics View the Port Information Administrator Administrator function, it provides the following functions Switch Setting IP Address „ MAC Address Table Entry Basic Switch SettingsAdvanced Setting Default is 300 seconds Miscellaneous Setting „ Igmp Theory of Operation Page Console Port Information Port Controls Trunking Aggregator setting Aggregator Information Aggregator Information State Activity Trunking State Activity interface Forwarding and Filtering Igmp Snooping Static MAC Address MAC filtering Vlan configuration Port-based Vlan Vlan PortBase interface 802.1Q Vlan „ Basic Acceptable Frame type Spanning Tree „ Forward Delay Time forward delay time System ConfigurationPer Port Configuration Port Mirroring Prot Mirroring interface Snmp Management „ System Options „ Trap Manager Security Manager„ Community strings 802.1X 802.1x Configuration Per Port Configuration Tftp Update Firmware Configuration Backup Tftp Restore Configuration Backup File Name fill the file name Factory DefaultTftp Backup Configuration „ Default IP address „ Default Gateway „ Subnet mask IP Stacking System RebootPanel List IP Stacking interface IP Stacking master switch configure finished interface IP Stacking Finished configuring interface „ Non-standard cables „ Faulty or loose cablesIncorrect connections „ Improper Network Topologies Diagnosing LED Indicators „ Cabling Connector Switch architectureLED Indicators Standard Safety DimensionsPower Supply MAC address