Lincoln Electric IM511-D Warnin G, RANGER 9 / LN-7 CONNECTION DIAGRAM, To Work, Electrode Cable

RANGER 9 / LN-7 CONNECTION DIAGRAM

WARNING

Do not operate with panels open.

Disconnect NEGATIVE (-) BATTERY LEAD before servicing.

Do not touch electrically live parts.

Keep guards in place.

Keep away from moving parts.

Only qualified personnel should install,use or service this equipment.

14PIN AMPHENOL

6PIN AMPHENOL

CAUTION :

TO WORK ELECTRODE

TO LN-7 INPUT

CABLE PLUG

OPTIONAL K857

REMOTE CONTROL

K584-XX INPUT CABLE ASSEMBLY

ELECTRODE CABLE

TO WIRE FEED UNIT

TO WORK

ANY INCREASE OF THE HIGH IDLE ENGINE RPM BY CHANGING THE GOVERNOR SETTING OR OVERRIDING THE THROTTLE LINKAGE WILL CAUSE AN INCREASE IN THE THE AC AUXILIARY VOLTAGE. IF THIS VOLTAGE GOES OVER 140 VOLTS, WIRE FEEDER CONTROL CIRCUITS MAY BE DAMAGED. THE ENGINE GOVERNOR SETTING IS PRE-SET AT THE FACTORY - DO NOT ADJUST ABOVE RPM SPECIFICATIONS LISTED IN

THE ENGINE WELDER OPERATING MANUAL.

N.A. USE POLARITY SWITCH TO SET FOR DESIRED ELECTRODE POLARITY. POSITION THE OUTPUT SELECTOR SWITCH TO A CV POSITION. PLACE WELDING TERMINALS SWITCH TO "REMOTELY CONTROLLED" POSITION.

N.B. WELDING CABLES MUST BE OF PROPER CAPACITY FOR THE CURRENT AND DUTY CYCLE OF IMMEDIATE AND FUTURE APPLICATIONS. SEE OPERATING MANUAL.

N.C. IF OPTIONAL REMOTE OUTPUT CONTROL IS USED, PLACE OUTPUT CONTROL SWITCH IN "OUTPUT CONTROL REMOTE" POSITIION. N.D. PLACE IDLER SWITCH IN "HIGH" IDLE POSITION.

12 - 16 - 93

M17092

RANGER 9 TO K867 ADAPTER CONNECTION DIAGRAM

WARNING
Do not operate with panels open.		Keep guards in place.
Disconnect NEGATIVE (-) BATTERY LEAD		Keep away from moving parts.
before servicing.		Only qualified personnel should install,use
Do not touch electrically live parts.		or service this equipment.
14 PIN		N.C.
AMPHENOL
	81
	82	NOT USED ON RANGER POWER SOURCES
	SPARE
K867 UNIVERSAL	2	CONNECT TOGETHER FOR
ADAPTER PLUG	4	N.D.
	41	WELDING OUTPUT
		42 VAC
	42
		N.E.
	31
		115 VAC
	32
TO WORK ELECTRODE
	GND	POWER SOURCE FRAME CONNECTION
ELECTRODE CABLE	21	WIRE FEEDER VOLTMETER CONNECTION
		CONNECTS TO (WORK TERMINAL) OF POWER SOURCE
TO WIRE FEED UNIT	77	10K
TO WORK	76	REMOTE OUTPUT CONTROL
	75	MIN.

CAUTION :

ANY INCREASE OF THE HIGH IDLE ENGINE RPM BY CHANGING THE GOVERNOR SETTING OR OVERRIDING THE THROTTLE LINKAGE WILL CAUSE AN INCREASE IN THE THE AC AUXILIARY VOLTAGE. IF THIS VOLTAGE GOES OVER 140 VOLTS, WIRE FEEDER CONTROL CIRCUITS MAY BE DAMAGED. THE ENGINE GOVERNOR SETTING IS PRE-SET AT THE FACTORY - DO NOT ADJUST ABOVE RPM SPECIFICATIONS LISTED IN

THE ENGINE WELDER OPERATING MANUAL.

N.A. WELDING CABLE MUST BE SIZED FOR CURRENT AND DUTY CYCLE OF APPLICATION.

N.B. USE POLARITY SWITCH TO SET DESIRED POLARITY, POSITION THE OUTPUT SELECTOR SWITCH TO A CV POSITION.

N.C. INSULATE EACH UNUSED LEAD INDIVIDUALLY.	{		2
N.D. FOR WIRE FEEDERS THAT RETURN A SIGNAL FOR WELDING OUTPUT, USE ISOLATION		TO
RELAY TO CLOSE LEADS 2 & 4.		K867
			4

N.E. REFER TO POWER SOURCE INSTRUCTION MANUAL FOR MAXIMUM AUXILIARY CURRENT DRAW.

TO WIRE FEEDER

12 - 16 - 93

M17093

– 32 –