K58 Magnetic Separator | Lincoln Electric LN-9F GMA, LN-9 GMA

C-7

C-7

ACCESSORIES

K58 MAGNETIC SEPARATOR

The K58 is a permanent magnet type separator designed to fit the top of the standard fill funnel of the continuous flux feed system.

The purpose of the separator is to remove magnetic materials such as mill scale and any other extraneous magnetic materials which may have been recovered along with the flux to be processed.

It is important to remove these magnetic particles from the flux which is to be reused in the continuous flux feeding system. If the magnetic material is not removed, it will gather around the nozzle of the gun and impede or shut off the flux flow when making rela- tively long welds or when welding continuously. The magnetic particles can also cause porosity in the weld.

Fit the magnetic separator into the funnel or hopper. Pour the flux to be reclaimed into the top pan of the separator. The separator is designed so that the flux flows around three permanent magnets. The magnets remove all magnetic particles. When the magnets become covered with their full load, they automatically stop the flux flow. When the flux flow stops, remove the separator from the funnel or hopper. Turn it over and open the panel that covers the magnets. Remove the magnetic particles by brushing or by using an air blast.

WARNING

WHEN USING COMPRESSED AIR BE CAREFUL TO PROTECT YOURSELF AND OTHERS IN THE AREA FROM FLYING PARTICLES.

NOTE: The magnetic separator is used with all Lincoln mild steel fluxes - 700 Series, 800 Series and 900 Series. Do not use the mag- netic separator with any stainless steel, alloy, or hardsurfacing flux except H-535. The mag- netic separator removes some of the alloying elements from these fluxes, thus changing their characteristics.

LN-9 GMA and LN-9F GMA Wire Feeder

Image 50

Lincoln Electric LN-9F GMA, LN-9 GMA manual K58 Magnetic Separator

Contents

LN-9 GMA and LN-9F GMA Wire Feeder Safety Depends on You Safety Electric Shock can kill Welding and Cutting Sparks can Cause fire or explosion Iii Précautions DE Sûreté Thank You TAbLE of Contents TAbLE OF CONTENTS cont’d Section F ViiiSection E P127, P125, P107 & P289 Series Width Height Technical SpecificationsLN-9 GMA and LN-9F GMA Wire Feeder Mounting the Wire Feed Unit Installing the LN-9 GMA Roll and 4-ROLL ModelsAttaching the Wire Reel Stand Mounting the Unit Routing the Electrode Power Input CAbLE ASSEMbLYElectrical Connections LN-9 GMA and LN-9F GMA Figure A.2 Strain Relief Clamp Figure A.3 LN-9F GMA Control bOX Installation Can kill Figure A.5 Connection of LN-9 GMA to DC-600 Power Sources Figure A.6 Connection of LN-9 GMA to DC-1000 Power Sources 75 76 77 Installation Figure A.9 Connection of LN-9 GMA to V300 Power Sources Machine Grounding Direct Work Lead Connection Connecting the GUN CAbLE to the Wire Feeder For GMA GUN CAbLES Hooking UP GMA Shielding GAS Cylinder may explode if damaged Safety Precautions Operating Instructions K424 LN-9 GMA 2-ROLL and K568-1 LN-9 GMA 4-ROLL General DescriptionRecommended Processes and Equipment K436 LN-9F GMA 2-ROLL and K583-1 LN-9F GMA 4-ROLL DC Constant Voltage Power Sources Controls and Settings Operation Operation Avoiding Grounding Lead Protector GLP Shutdown Power Supply FuseCircuit Protection and Automatic Shutdown Circuit bREAKER Automatic Shutdown Drive Roll Installation Changing Drive Rolls for 2-ROLL Wire Feeders Guide Tube Detail Changing Drive Rolls for 4-ROLL Wire Feeders Large Wire Loading Figure b.7a Threaded Locking Collar Loading a 50-60 Lb .7-27.2 KG. Coil Using K1504-1 Coil Reel Feeding Electrode and bRAKE Adjustment ADJUSTAbLE Wire Reel bRAKE Loading a 50 or 60 Lb. Coil Loading and Feeding 13-14 Lb Innershield Coils K378 Reel Mounting Stand For TWO-ROLL Feeders Pressure Adjustment Knob Idle Roll Pressure SettingRoll Wire Feeders Pulse Power 500, DC650 PRO CV-400, CV-500-I Adjust the Power SourceAdjust the LN-9 GMA Controls DC-250, DC-400, or DC-600 Voltage Control Response Starting CharacteristicsRUN-IN Feature Select Acceleration Making a Weld Procedure AT END of CoilSecurity of Weld Procedure Settings Wire Reel Stands and Mountings Optional Equipment and AccessoriesPower Input CAbLE ASSEMbLIES K196, K595, K596 Auxiliary Equipment Contacts Spindle for READI-REELS and 2 I.D. Spools K162-H Attaching the Wire Reel StandsWire Reel Door KIT READI-REEL Adapters Universal Wire Reel Stand K1524-1 Wire Feeder Accessories BURNbACK Timer KIT K419 Dual Procedure KIT K319 GMA Timer KIT K418Dual Process KIT K317 For Wire Feeders Pulse Power Filter Conversion KIT K442-1 Continuous Flux Feed Tank K320 Swivel Platform K178-1Undercarriage K163 K320 Flux Tank Loading K58 Magnetic Separator Cored Electrode TAbLE C.2 Drive Roll and Guide TUbE KitsKit Roll Solid Steel Electrode Aluminum Electrode Coils with 1 Spindle Routine MaintenancePeriodic Maintenance Adapter Proper Speed Sensor Module Mounting Figure D.1 Speed Sensor Module Location Figure D.2 LN-9 GMA Connectors Figure D.2 Switch Requirements TROUbLESHOOTING TROUbLESHOOTING Guide Wire Feeding PRObLEMS Gun trigger will not feed wire. Digital meter is not lit Grounding Lead Protector Shutdown in the Operation section TROUbLESHOOTING Welding PRObLEMS Starting Characteristics LN-9 GMA WIRING Wire LN-9F GMA LN-9 GMA Dimension Print LN-9F GMA Dimension Print 1 Wire Drive Unit LN-9F Dimension Print 2 Control bOXPage Precaucion LN-9 GMA Wire Feeder Keep your head out of fumes