iii

SAFETY

iii

Return to Master TOC

Return to Master TOC

Return to Master TOC

WELDING SPARKS can cause fire or explosion.

6.a. Remove fire hazards from the welding area. If this is not possible, cover them to prevent the welding sparks from starting a fire. Remember that welding sparks and hot

materials from welding can easily go through small cracks and openings to adjacent areas. Avoid welding near hydraulic lines. Have a fire extinguisher readily available.

6.b. Where compressed gases are to be used at the job site, special precautions should be used to prevent hazardous situations. Refer to “Safety in Welding and Cutting” (ANSI Standard Z49.1) and the operating information for the equipment being used.

6.c. When not welding, make certain no part of the electrode circuit is touching the work or ground. Accidental contact can cause overheating and create a fire hazard.

6.d. Do not heat, cut or weld tanks, drums or containers until the proper steps have been taken to insure that such procedures will not cause flammable or toxic vapors from substances inside. They can cause an explosion even though they have been “cleaned”. For information, purchase “Recommended Safe Practices for the Preparation for Welding and Cutting of Containers and Piping That Have Held Hazardous Substances”, AWS F4.1 from the American Welding Society (see address above).

6.e. Vent hollow castings or containers before heating, cutting or welding. They may explode.

6.f. Sparks and spatter are thrown from the welding arc. Wear oil free protective garments such as leather gloves, heavy shirt, cuffless trousers, high shoes and a cap over your hair. Wear ear plugs when welding out of position or in confined places. Always wear safety glasses with side shields when in a welding area.

6.g. Connect the work cable to the work as close to the welding area as practical. Work cables connected to the building framework or other locations away from the welding area increase the possibility of the welding current passing through lifting chains, crane cables or other alternate circuits. This can create fire hazards or overheat lifting chains or cables until they fail.

6.h. Also see item 1.c.

CYLINDER may explode if damaged.

7.a. Use only compressed gas cylinders

containing the correct shielding gas for the process used and properly operating regulators designed for the gas and

pressure used. All hoses, fittings, etc. should be suitable for the application and maintained in good condition.

7.b. Always keep cylinders in an upright position securely chained to an undercarriage or fixed support.

7.c. Cylinders should be located:

Away from areas where they may be struck or subjected to physical damage.

A safe distance from arc welding or cutting operations and any other source of heat, sparks, or flame.

7.d. Never allow the electrode, electrode holder or any other electrically “hot” parts to touch a cylinder.

7.e. Keep your head and face away from the cylinder valve outlet when opening the cylinder valve.

7.f. Valve protection caps should always be in place and hand tight except when the cylinder is in use or connected for use.

7.g. Read and follow the instructions on compressed gas cylinders, associated equipment, and CGA publication P-l, “Precautions for Safe Handling of Compressed Gases in Cylinders,” available from the Compressed Gas Association 1235 Jefferson Davis Highway, Arlington, VA 22202.

FOR ELECTRICALLY powered equipment.

8.a. Turn off input power using the disconnect switch at the fuse box before working on the equipment.

8.b. Install equipment in accordance with the U.S. National Electrical Code, all local codes and the manufacturer’s recommendations.

8.c. Ground the equipment in accordance with the U.S. National Electrical Code and the manufacturer’s recommendations.

Return to Master TOC

Mar ‘95

Page 4
Image 4
Lincoln Electric NA-5NF, NA-5SF Cylinder may explode if damaged, Welding Sparks can cause fire or explosion

NA-5S, NA-5N, NA-5SF, NA-5NF specifications

The Lincoln Electric NA-5NF, NA-5SF, NA-5N, and NA-5S are advanced welding helmets that are pivotal in enhancing the safety and efficiency of welders in various applications. These models are designed to provide exceptional protection and visibility, making them indispensable tools in the welding industry.

One of the main features of the NA-5 series is the auto-darkening filter technology. This feature allows the helmet to automatically adjust its shade based on the intensity of the arc. As the welder strikes an arc, the lens darkens instantaneously, shielding the eyes from harmful rays generated during the welding process. This functionality not only ensures safety but also enhances productivity, as welders do not need to manually flip the helmet up and down.

The helmets are equipped with a wide viewing area that allows for better visibility and precision while working. With a large lens, welders can easily monitor their work and surrounding environment, minimizing the risk of accidents. Additionally, the lightweight design of the NA-5NF, NA-5SF, NA-5N, and NA-5S provides comfort during extended periods of use, reducing neck strain and fatigue.

The NA-5 series is also well-regarded for its durability. Constructed from impact-resistant materials, these helmets can withstand the rigors of demanding work environments. This durability extends the lifespan of the helmet, making it a cost-effective investment for both professional and hobbyist welders.

Another notable characteristic is the adjustable sensitivity and delay settings found in certain models. These settings allow the user to customize the helmet based on their specific welding conditions. For instance, a welder can increase sensitivity for low-amperage tasks or adjust the delay to allow for a smoother transition from dark to light after completing a weld.

Furthermore, the helmets come with a reliable battery life, ensuring that they can be used for long periods without interruption. Some models also feature solar assist functionality, which helps recharge the auto-darkening filter, enhancing their overall efficiency.

In summary, the Lincoln Electric NA-5NF, NA-5SF, NA-5N, and NA-5S welding helmets represent a significant advancement in personal protective equipment for welders. Their combination of auto-darkening technology, wide viewing area, lightweight design, durability, and customizable settings makes them an excellent choice for anyone engaged in welding tasks. With these helmets, users can achieve greater safety and efficiency in their work, enabling them to focus on their craft with peace of mind.