Return to Section TOC
Return to Section TOC
Return to Section TOC
Return to Section TOC
Return to Master TOC
Return to Master TOC
Return to Master TOC
Return to Master TOC
| TROUBLESHOOTING & REPAIR | |
| TROUBLESHOOTING GUIDE | Observe Safety Guidelines |
|
| detailed in the beginning of this manual. |
PROBLEMS | POSSIBLE AREAS OF | RECOMMENDED |
| ||||||
(SYMPTOMS) | MISADJUSTMENT(S) | COURSE OF ACTION | |||||||
|
|
|
|
|
|
|
| ||
|
| FUNCTION PROBLEMS |
|
|
|
|
| ||
All the status lights begin to blink | 1. | Make sure the | 1. | Perform | the | Primary Power | |||
within 5 seconds of power up. |
| reconnected correctly for the |
| Board Resistance | Test and | ||||
|
| input voltage being applied. Be |
| Capacitor Voltage Test. | |||||
|
| sure to remove input power | 2. Perform the Input Rectifier | ||||||
|
| and wait at least one minute | |||||||
|
|
| Test. |
|
|
| |||
|
| before changing the position |
|
|
|
| |||
|
|
|
|
|
|
| |||
|
| of the input voltage range | 3. | The control board may be | |||||
|
| switch. |
|
|
| faulty. Replace. |
| ||
|
|
|
|
| 4. The primary power board may | ||||
|
|
|
|
|
| be faulty. Replace. |
| ||
|
|
|
| ||||||
The machine powers up properly, | 1. Make sure the torch is connect- | 1. | Perform the Auxiliary Trans- | ||||||
but there is no response when the |
| ed properly to the |
| former Test. |
|
| |||
gun trigger is pulled. Only the |
| machine. |
|
| 2. | Perform | the | Trigger Circuit | |
power LED is lit. |
|
|
|
| |||||
2. Make sure the air supply is con- |
| Test. |
|
|
| ||||
|
|
|
|
| |||||
|
| nected and operating properly. | 3. | Perform | the | Gas | Solenoid | ||
|
|
|
|
| |||||
| 3. | Make sure the torch head con- |
| Test. |
|
|
| ||
|
| sumable parts are in place and | 4. Perform the Torch Continuity | ||||||
|
| in good condition. | Replace if | ||||||
|
|
| and Solenoid Test. |
| |||||
|
| necessary. |
|
|
|
| |||
|
|
|
|
|
|
|
|
| |
|
|
|
|
| 5. The control | board | may be | ||
|
|
|
|
|
| faulty. Replace. |
| ||
|
|
|
|
| 6. The output power board may | ||||
|
|
|
|
|
| be faulty. Perform the Output | |||
|
|
|
|
|
| Board Resistance Test. | |||
|
|
|
|
| |||||
When the torch trigger is pulled, air | 1. Make sure | the torch consum- | 1. | Perform the Torch Continuity | |||||
begins to flow; but no pilot arc is |
| ables are in place and in good |
| and Solenoid Test. |
| ||||
established. |
| condition. | Replace if neces- | 2. | Perform | the | Low | Voltage | |
|
| sary. |
|
| |||||
|
|
|
|
| Circuit Test. |
|
| ||
|
|
|
|
|
|
|
| ||
| 2. | Make sure | the air | pressure is | 3. The output board may be faulty. | ||||
|
| set at 70 psi (448 kPa.) | |||||||
|
|
| Perform | the | Output Board | ||||
|
|
|
|
|
| ||||
| 3. | Make sure there are no kinks or |
| Resistance Test. |
| ||||
|
| restrictions | for air | flow in the | 4. The control board may be | ||||
|
| torch cable. |
|
| |||||
|
|
|
|
| faulty. Replace. |
| |||
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
CAUTION
If for any reason you do not understand the test procedures or are unable to perform the test/repairs safely, con- tact the Lincoln Electric Service Department for electrical troubleshooting assistance before you proceed. Call
