DXS-31 DOOR/WINDOW SENSORS

◆The DXS-31 sensors can be used to monitor doors, windows, cabinets, crawl space doors, gates, freezer doors, and many other moving objects that could be used for intrusion or need to be monitored.

◆A built-in magnetic switch triggers the sensor when its magnet (mounted on the moving part or the door or window) moves away from the sensor.

◆External normally closed switches can be wired to the sensor for remote triggering.

◆The door/window sensor can connect directly to a glass break detector.

SET SENSOR JUMPER

◆A jumper inside the door/window sensor selects instant or delayed response.

If the sensor is going to be used on the primary entry/exit door make sure that the jumper is in the DELAY position.

If the sensor is going to be used on a window or a door that is not going to be used to enter and exit the premises, set the jumper to the INSTANT position.

APPLY DOUBLE-STICK TAPE

Apply double-stick tape (supplied) to back of sensors and magnets.

◆Screws are also provided to mount sensors and magnets.

◆Screws are preferred over the double-stick tape in permanent installations.

✍UL NOTE: Double-stick tape is not allowed in UL installations.

ATTACH SENSORS AND MAGNETS

On doors, mount sensor to door frame and magnet to door.

✍NOTE: Magnet must line up with mark on sensor case both horizontally & vertically.

Allow a maximum of 1/2" between magnet

and sensor when door/window is closed. Snap sensor onto mounting plate.

On windows, mount sensor to window frame and magnet to window.

Snap sensor onto mounting plate.

The magnet height is adjustable and an optional magnet spacer is provided for uneven surfaces.

EXAMPLE INSTALLATIONS

LEFT OPENING DOOR

SLIDING WINDOW

TRANSMITTER

MOUNTED ON

DOOR JAMB

MAGNET MOUNTED

ON WINDOW FRAME

(NOTE: SMALL END OF TRANSMITTER UP)

MAGNET MOUNTED

ON DOOR

TRANSMITTER

MOUNTED ON

WINDOW SILL

RIGHT OPENING DOOR

DOUBLE-HUNG

 

 

WINDOW

TRANSMITTER

TRANSMITTER

MOUNTED ON

MOUNTED ON

WINDOW FRAME

DOOR JAMB

 

(NOTE: SMALL END

 

OF TRANSMITTER DOWN)

MAGNET

MAGNET MOUNTED

MOUNTED

ON WINDOW

ON DOOR

SASH STILE

 

INSTANT/DELAY

ANTENNA

 

OPTION JUMPER

 

INPUT

MAGNET

TWO TYPE 2032

ALIGNMENT

SELECT

MARK

BATTERIES

JUMPER

 

 

 

 

BATTERY

 

 

CLAMP

TRANSMIT

 

SCREW

 

 

INDICATOR

 

 

 

 

BATTERY CLAMP

TEST

 

EXTERNAL

SWITCH

 

 

INPUT

 

 

 

 

TERMINALS

INSTANT/DELAY

OPTION JUMPERSELECTS

INSTANT

SELECTS

DELAY

ATTACH MOUNTING PLATES

USING THE SCREWS OR

DOUBLE-STICK TAPE PROVIDED

NOTE: ATTACHING THE TRANSMITTER WITH DOUBLE-STICK

TAPE IS NOT ALLOWED IN UL INSTALLATIONS

TEST SENSORS

❇Console in Chime Mode should “ding-dong” when the sensor sends signal.

Open door or window.

❇Verify that light on the sensor glows momentarily when door/window is opened.

❇Status indicator on Console should remain lit for each door/window sensor that is left open.

OPEN DOOR, TRANSMIT INDICATOR SHOULD LIGHT

1.PLACE RECEIVER INTO PROGRAM OR "LEARN" MODE

2.ACTIVATE TRANSMITTER BY OPENING DOOR OR WINDOW

3.VERIFY THAT THE RECEIVER ACCEPTED THE SIGNAL

4.REPLACE TRANSMITTER COVER WHEN FINISHED

NOTE: THE TRANSMIT INDICATOR WILL ONLY LIGHT DURING TRANSMISSIONS WHEN THE CASE IS OPEN (EXCEPT WHEN PUSHING THE CASE FOR TESTING)

15